Jump to content
SAU Community

Different Plugs On The Loom?

Rude Carz

By Rude Carz,
in General Maintenance

 Share

Recommended Posts

Rude Carz Enthusiast

Rude Carz

Posted
Posted (edited)

hey kids

mucking round with a mate last night after getting a new for the rb26 and one of the main plugs is different.

few questions -

- If you pull the CAS out when the key is turned twice and everything is priming, if you turn the key on the CAS should it fire the injectors?

- The fuel pump isnt priming. it was with the old loom and not with the new one, the main thing is that plug isnt plugged in

can anyone help me?

thanks

Dan

pics!!

100_8049-1.jpg

100_8048.jpg

^^^ THAT IS PART OF THE ENGINE LOOM BUT ISNT ATTACHED TO THE LOOM I HAVE ^^^

100_8047.jpg

^^^ THAT IS THE NEW LOOM ^^^

Edited by Rude Carz
Link to comment
https://www.sau.com.au/forums/topic/195015-different-plugs-on-the-loom/
Share on other sites
blur Proficient

blur

Posted
Posted

Thats a R33 loom and those wires are for knock sensors and cold air idle up valve and possibly something else. Should start with that disconnected, but i wouldnt drive it like that though, just in case. theres quite a few different plugs between r33 and 32. Id try and get a 32 loom.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...