Jump to content
SAU Community

Recommended Posts

Hi guys I'm pretty sure this plug is for the factory mobile setup, but does anyone recognise what phone it would plug into? would it be worth changing the plug to match my Nokia phone plug? How easy would it be to change it?

cheers

post-927-1195893234_thumb.jpg

post-927-1195893277_thumb.jpg

post-927-1195893338_thumb.jpg

Edited by vspec2
Link to comment
https://www.sau.com.au/forums/topic/195049-v35-factory-mobile-phone-setup/
Share on other sites

that said if its like every other dealer fit option I've seen onthese It can be modded to take another nokia - benz did a similar thing.

Chris

You're like an encyclopedia, thanks mate!!!

I'll give you call about the DVD headunit sometime this week.

cheers

Alain

That's cool! I've read about it, but haven't seen that before. Does the other side of the steering wheel have controls for the stereo?

What model is your car?

Might want to check to see if it can connect by bluetooth because I have read that it was an option.

Hi no controls on the other side. the top and bottom buttons control the stereo volume and change tracks and radio stations.

2005 6MT

No Bluetooth I'm afraid tested that a while back.

cheers

That's cool! I've read about it, but haven't seen that before. Does the other side of the steering wheel have controls for the stereo?

What model is your car?

Might want to check to see if it can connect by bluetooth because I have read that it was an option.

would LOVE to play with this. (especially since it was a dealer fitted option..) anyone in brissy got this?

Hi Chris , got 1 off the wharf today 05 6sp , ready to comply , will have to ring you and talk . on the southside of brissy as well .

Regards Brad

brad,

thanks for today.

for the record that unit is BUILT INTO the car similar to what lexus did in the 90s with motorola. my thoughts would be to find the phone that runs it and use that. nothing else can be used. this info is based on the above car.

Hi guys I'm pretty sure this plug is for the factory mobile setup, but does anyone recognise what phone it would plug into? would it be worth changing the plug to match my Nokia phone plug? How easy would it be to change it?

cheers

Hi, I just picked up my 6mt 06 last week after a lot of red tape, it too has the same phone connection.

Is there a way to get the bluetooth to work?

Hi

The buttons are for the phone only so they dont control any audio controls. When you press the phone button it displays the phone menu on the sat/nav screen prob shows phone info etc.. If I can find a phone that actual works with it I will give an update.

cheers

hey guys,

i have the same phone connector in my car.. I went through the manual and it says that it is only compatible with au phones. For those who don't know au is a CMDA-1 phone network run by KDDI in Japan. There are quite a few phones designed for au by different manufacturers so I am assuming that all of these phones must have the same connector? Check the lineup here.

There's a Sanyo phone there under global passport which is gsm and cdma so that should work.. But I really would prefer a phone adapter :)

Just did a bit more digging... you basically need the reverse of this cable.. I actually have an adapter that does the same thing.. just need to reverse the flat connector

nissyann_ga2-img600x450-1195474004dscn0052.jpg

Edited by karim
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...