Jump to content
SAU Community

Recommended Posts

Hey,

I made a couple posts in the "car not accellerating propperly" thread, but still having problems with my car. It's a 1990 R32 gts-t

Here are my current modifications:

pod filter

3" cat-back exhaust

FMIC

Here is my problem:

When the car is hot, if i accellerate hard, the engine pops and misfires at about 3500rpm. Only happens under load and only when i've been driving for about 5 mins or so and it's nice n warm.

Here's what i've done so far to try and fix it:

Upgraded fuel pump to one from an R33 GTR

New spark plugs

Replaced coils with 2nd hand ones from another 32 gts-t

Not sure what's going wrong.. seems like it's a fuel or ignition problem, but i can't quite tie it down. I put in a fuel mixture display kit from Jaycar to see if it was rich or lean when it spits n pops, but the lights just flash from lean to rich and back over n over again.

I'm pretty much out of ideas. Maybe i need to upgrade coils. Maybe i should try regapping the spark plugs.. i really don't know anymore.

Any advice or suggestions would be greatly appreciated. May end up that i'll just have to take it to a garage with a dyno to get it diagnosed. better start saving my $$

Link to comment
https://www.sau.com.au/forums/topic/195931-car-problems/
Share on other sites

put in an autotechnica fuel pressure regulator.. i don't recommend them.. crappy cheap parts, broke in a couple places, but managed to get it working in the end.

fuel pressure was only 35psi when idling.. upped it to 60psi at idle and seems to have fixed the problem.. more testing (aka fanging it) needed, but signs look good.

Thanks Gaz n Pal for the suggestions.

Link to comment
https://www.sau.com.au/forums/topic/195931-car-problems/#findComment-3509249
Share on other sites

try a new air flow meter.....

my afm was dicky when the car got hot and i did all the usual 'obivous' quick fixes such as

-changed my igniter module

-changed all 6 coilpacks

-put in new plugs and gapped them to .6mm

-changed air filter and changed fuel filter

problem ended up being the air flow meter was faulty.... give ben at KYP a call

Edited by Pandaah32
Link to comment
https://www.sau.com.au/forums/topic/195931-car-problems/#findComment-3515414
Share on other sites

hahaha.. maybe you can donate me the cash mr engineer sir.

but yeah.. me n Steve found tonight that my coils are arcing onto the block seems the "new" coils were about the same condition as the old ones. gonna araldite them and reduce the plug gap.. should do the trick.

Link to comment
https://www.sau.com.au/forums/topic/195931-car-problems/#findComment-3518287
Share on other sites

I've got a set of standard 32gtst coils doing nothing other than taking up space.. they were working well enough to make 245rwhp on the RB20 :nyaanyaa:

Or a set of splitfired aren't too pricey, I got mine for $515 delivered I think it was.

Link to comment
https://www.sau.com.au/forums/topic/195931-car-problems/#findComment-3518768
Share on other sites

ok this is really annoying me now.. problem is still happening with araldited coils and spaller plug gaps.. gonna try air flow meter next.. Were you getting the same symptoms when your airflow meter was faulty Pandaah?

next to try after that will be ignition module.. how do i go about testing that?

Edited by Wogan
Link to comment
https://www.sau.com.au/forums/topic/195931-car-problems/#findComment-3520809
Share on other sites

another thing i find interesting is that my car is making about 12psi of boost without a boost controller installed.. inspected the wastegate actuator and the hose feeding it, but they seemed fine. The previous owner hadn't done much work to the car and didn't have a working boost gauge.

could it be that i'm getting too much boost and the standard ECU is cutting the fuel?

Link to comment
https://www.sau.com.au/forums/topic/195931-car-problems/#findComment-3520822
Share on other sites

ok this is really annoying me now.. problem is still happening with araldited coils and spaller plug gaps.. gonna try air flow meter next.. Were you getting the same symptoms when your airflow meter was faulty Pandaah?

next to try after that will be ignition module.. how do i go about testing that?

borrow one from someone else or throw it on a dyno for a full diagnostic run

if your running stock ecu they can check what the prob is if they have the software

Link to comment
https://www.sau.com.au/forums/topic/195931-car-problems/#findComment-3520849
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...