Jump to content
SAU Community

Sqeeky Loosy Rattle Noise (33)

jake33

By jake33,
in Engines & Forced Induction

 Share

Recommended Posts

jake33 Experienced

jake33

Posted
Posted

It seems to happen after ive been driving and the car has been warmed up.

Sitting at idle the noise seems to be coming from maybe the belts and around the turbo side (i dare say..)

Not 100% sure, it doesnt seem to be comming from the actual belts and ive had a 100k service done where the water pump and tensior and timming belts were changed (3000ks ago).

While stationary if i put the clutch in, the noise stops then when off the clutch the noise starts up.

anyone had similar probs or know what could be up?

driving me a little crazy.

cheers

Link to comment
https://www.sau.com.au/forums/topic/196406-sqeeky-loosy-rattle-noise-33/
Share on other sites
jake33 Experienced

jake33

Posted
  • Author
Posted

ah k, well searched throw out bearing, couldnt find too much on price to fix, if its easy to fix and is it a major critical thing. (dangerous to drive?)?

its been going on for a couple of weeks. im glad its not the turbo (well.. hopefully its not)

where is this throw out bearing located?? on car and to be purchased?

getting a tune at Creatd this friday so ill word em up about it.

any other ideas?

cheers

Pandaah32 Rookie

Pandaah32

Posted
Posted

gearbox just needs to come out.. try and find who will do that for the cheapest, and no the car isnt dangerous to drive even tho the bearings making noise it'll probly just get louder but youll find if your lacking money atm (chrissy time and all) you could possibly drive with it like that for ages...

Simmo1985 Community Regular

Simmo1985

Posted
Posted

Mine's doing it at the moment. Been doing it for about 2 months. I'm getting my clutch replacing on Friday though. They'll replace the bearing then, it's located near your clutch. Not sure where to go to buy the throw-out bearing separately. Maybe ask Slide or Kudos (traders). They sell exedy clutches so they should be able to source a bearing for you.

But yeah, don't stress about it at the moment. It's just annoying, not dangerous.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      He means "as opposed to mechanical cable drive". Older cars (R32 for ex.) had cable drive. Later cars with essentially the same gearbox, ie R34 GT (NA RB25) used essentially the same box as the R32 GTSt, but instead of a cable drive, had an electronic speed sender plugged into the same hole in the box, running from the same little gear that would have run the cable. Some of the shittier later cars use a speed sender on the nose of the diff, or the ABS sensors.
    • GTSBoy
      Hypergear Turbochargers and High flow Services Development thread

      By GTSBoy · Posted

      Lower than engine, or lower than it should at the hubs? Either way, that is a nice power figure and I'm not surprised you say it rips now. What stopped you from turning it up any more? Injectors? Or did it just stop responding to boost?
    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      Got my 34 gtt tuned last week. Car made 362 wheel horsepower at 19 psi. Turbo was the ATR43SS. Only other upgrades were haltech 2000 series. 650cc injectors, walbro 250, fmic. Pro hub dyno reads 6% lower than actual figure according to my tuner. Car is a real ripper now.  IMG_7261.mov
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Hi everyone, I'm wondering if anyone in Melbourne (preferably West) has a non-S2 R34 front bar. If it's already off the car, even better!  Nothing too weird, I just need to get a cut-out of the hole that the front indicators clip into 🤣 (image attached for reference)   I've got a front bar from JSAI Aero, but those holes need to be cut myself, and I want to get it right so the indicators will clip securely. And my OEM bumper is a S2, so I have no reference. So looking for a member who might be able to spare me a few minutes to make a cardboard cut-out using your front bar.
×
×
  • Create New...