Jump to content
SAU Community

Future plans for us turkeys and our cars :) care of gordo


Recommended Posts

  • Replies 160
  • Created
  • Last Reply

Top Posters In This Topic

yeah predator, i was thinking do the paint/body and leave it, sell it

no point putting too much more into it, but if i do ill be keeping the car for another couple of years

but id much prefer a better platform or more so, not lose too much money when selling the R33

the bonnet if u looked closely was pretty shocking, i had these weird stains on it that were under the gloss and under fluro light u can see some shocking shades :S

Well as far as my mods go I'm picking up my C's short shift kit tomorrow....

Then in a couple months time go PowerFC + hand controller + boost control kit... already used to the current power....

err..yes jet.. you will have the fastest.

as long as you don't throw a piston or something no, you won't have to worry about anybody getting anything remotely close to 400rwkw anytime soon :D

Jack: yours will go even more like stink then, scary!

There just is something about that GTR powerslide.. was admiring it Saturday from behind :D

Mine is back to stock, and while it hasn't got any power now :( it just feels "more complete" right across the range like the stock ECU isn't playing "catchup". I'm thnking that is what a proper ECU properly installed must be like, like a came out of the factory with XXX kw

ha - i'm 27 on Saturday... makes u realise cars can't hold u too back in life. I guess at 21 i woula been all go go go but i was still at uni then where life was cheap :D Gotta think about boring stuff like buying a house myself pretty soon b4 it all gets too expensive.

hmm.. off track.. oops, this thread is interesting - don't want it closed

anybody else got car plans wanna jump in the thread ?? :(

argh, when i was running the stock ecu with all the gear off bar the intercooler the power was all over the place through out the rev range

huge flat spots here and there, was frustrating at times

but it feels good to be dead stock in the morning passing your EPA, then getting your hands into it and putting every back on my 7pm that night instantly getting your power back

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • How would you even adjust the clutch if the pedal already has the correct free play? The operating cylinder has no adjustment in mounting position or rod length. On pull style clutches there is also no ability to adjust the bearing carrier. Push type I can see how adjusting the carrier height makes it all work.   If this is the twin plate clutch did you verify that your friction disks were oriented correctly? It's not mentioned in the directions at all you just have to notice that one side the friction disks have a part number on the hub fingers and a subtle coning to those fingers. Another thing that I noticed was if you put the friction disks in backwards the pressure plate fingers will not be even and flat when the clutch is installed.
    • yeah, mechanically, it is probably do-able, off the top of my head, there would be the transfer case, which I believe will bolt up to the rear of the RWD transmission, the shorter rear tail shaft. A front drive shaft, front diff, engine upper sump, front drive shafts, front hubs and front AWD struts (they are shaped around the front drive shafts), LCAs (at the very least from the front suspension) oil cooler.  You might want the rear diff from an AWD too, so you can be certain the front and rear diff rations are identical.  Who knows what brackets and mounts you might need.  So a whole doner car might be the best option if you need to maintain RHD. Then actually making it work, that would be a whole different story.
    • Take the fall as a warning sign for future endeavours  Stay safe mate
    • hi mate, HKS cooler piping still available by any chance?
×
×
  • Create New...