Jump to content
SAU Community

Recommended Posts

Hey guys and girls.. I have 2 Bov i need to get rid off.. One is a TurboSmart V Port II and the other is a GFB Stealth FX

I have had them bought for abour 1 year now.. I've gone back to my stock BOV

They are in Very good condition, Pretty much like new..

I'm asking around $250 each ono.. will not turn down any serious offer.

I bought these brand new and they almost cost me like $450 each.

They are a direct bolt on to the R33. The GFB BOV has 2 vents.. one plums back in to the intake and the other vents outside

I'm located in melb, West...

Call me on 0421 205 751

post-19580-1196915020_thumb.jpg

post-19580-1196915716_thumb.jpg

Edited by Dush
Link to comment
https://www.sau.com.au/forums/topic/196540-turbo-smart-gfb-bovs/
Share on other sites

Yea mate. it come with the Original turbo smart adaptor. These 2 BOV's are a direct fit to the R33's.. no midifications need to be done.. i just need em gone.

I need a the asap so I will not turn down any offer.. so yea..

If they dont sell i'm just gonna put em up on ebay and take what eva i get for em..

hey mate

which version of your GFB bov is it? adj noise one?

Yea mate, i can adjust the noise buy turning the head left or right in the direction of plumback or vet to atmospher..

can you block it up to make it full plumb back? or the knob makes it 100% plum back? so theres 100% atmo or 100% plumb back and 50/50?

Yes thats right... turn the knob 100% to the left and its plumback.. right.. atmo..

GFB STEALTH FX SOLD TO 265KW AT THE WHEELS HOLMES -- PENDING PAYMENT

Turbosmart V port 2 still up for sale...

Edited by Dush

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...