Jump to content
SAU Community

Scantools

wabbo69

By wabbo69,
in V Series (V35, V36, V37 & Infiniti)

 Share

Recommended Posts

wabbo69 Enthusiast

wabbo69

Posted
Posted

Wondering if anyone has cracked the OBD2 consult 2 side of the V35 yet in regard to using a P.C and Interface plugged into the consult port under the dash and can offer advice.

I have scanners that I used on other cars and interfaces but not sure how to go about accessing the internals of the V35. Consult 2 is too expensive for me.

Following on from that what can you access, what does it mean and what can you change?

Gibbo

Link to comment
https://www.sau.com.au/forums/topic/198016-scantools/
Share on other sites
TomR33 Collaborator

TomR33

Posted
Posted
Wondering if anyone has cracked the OBD2 consult 2 side of the V35 yet in regard to using a P.C and Interface plugged into the consult port under the dash and can offer advice.

I have scanners that I used on other cars and interfaces but not sure how to go about accessing the internals of the V35. Consult 2 is too expensive for me.

Following on from that what can you access, what does it mean and what can you change?

Gibbo

I have. The OBDII protocol is no bigge it's just a standard protocol but you can't do much with it. I'm currently working on Nissan Data Scan II that will work with Consult II protocol. So far I can monitor most parameters and registers. The final product will also let you log data, adjust idle speed and ignition timing as well as reading and clearing error codes. The NDS II software and PC adaptor will be available through Blazt.biz.

Cheers,

Tom

Link to comment
https://www.sau.com.au/forums/topic/198016-scantools/#findComment-3537961
Share on other sites
NA_R33 Grand Master

NA_R33

Posted
Posted

I have the Autoenginuity Scantool and it is very limited with the V35 as JDM cars do not run the OBD-II interface, they use a different protocol, not even Nissan's Nissan Consult at a service department could talk to the car.

Link to comment
https://www.sau.com.au/forums/topic/198016-scantools/#findComment-3539974
Share on other sites
wabbo69 Enthusiast

wabbo69

Posted
  • Author
Posted

Consult_Protocol___Commands_Issue_6.pdfWill see as tomorrow it goes in to the local dealership. I think the issue is more the Nissan proprietry code or extensions that it uses.

The G35 guys say consult 2 works and I see no reason why it would not. I think the skill level of the Nissan Technicain comes into play here not so much the tool.

This is the Consult Protocol attached.

Link to comment
https://www.sau.com.au/forums/topic/198016-scantools/#findComment-3539999
Share on other sites
TomR33 Collaborator

TomR33

Posted
Posted

Yeah, thats the Consult I protocol from PLMS website prepared by Nissan Technical Group. Completely different to Consult II protocol and can't be used on our v35 Skylines.

The Consult II unit from Nissan dealership will work but do you want to spend $2500 to get one?

Tom

Link to comment
https://www.sau.com.au/forums/topic/198016-scantools/#findComment-3540790
Share on other sites
  • 6 months later...
Chris Rogers Grand Master

Chris Rogers

Posted
Posted

http://www.nissantechmate.com/detail.aspx?id=513

need someone in the USA to get it though. they will not ship outside the USA and if you email them you will end up with a call from repco here in Oz. the machine that repco offer does not work on a 2001-2004 v35 but does on a 2004.5 up.

look at the launch x413 if you want to play with the internals of that car. as for software packages - no real idea - I use scanners.

Link to comment
https://www.sau.com.au/forums/topic/198016-scantools/#findComment-3962499
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      NC MX5

      By Duncan · Posted

      There was a great one on Victoria Rd in Gladesville too back in the day. I can only assume GTSBoy is thinking of the mill up on the wollondilly, no restaurant there any more but they have restored the original steam engine on site and run it every few months, have an annual steampunk festival etc @The Bogan, you came to the wrong town for restaurants. we have a few reasonable asian and indian options but the Paragon is as good as it gets otherwise. That brewery is apparently just opened, been meaning to give it a go some time. The Highlands have plenty of fancy options but I suspect you are more a hearty eater than fancy eater
    • Duncan
      Squeaking clutch/throw out bearing

      By Duncan · Posted

      Thanks for coming back to post the update, maybe it will help out the next person!
    • WMDC35
      Engine model

      By WMDC35 · Posted

      Going by the intake & injectors I'd be guessing it's a DE, check the head casting number, should be 5L8 on a DET, 5L7 I think is the DE number.
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      For future reference, if you need to use Deutsch connectors but don't have the proper crimper for the round style pins, you can get regular style crimp pins too
    • GTSBoy
      Engine model

      By GTSBoy · Posted

      No. The castings are all the same. As you have the inlet off, simply measure the diameter of the inlet ports and compare with the freely available on the net sizes of turbo and NA. The NA ones are small.  
×
×
  • Create New...