Jump to content
SAU Community

Wheel Alignment Tyresaver Or Performance?

(B1) MR_fanny
 Share

Recommended Posts

(B1) MR_fanny Grand Master

(B1) MR_fanny

Posted
Posted

so due to a defect i got new advan v103's, camber kits and a tyre saver wheel alignment. the car now feels very floaty at the steering wheel which im not liking. the car previously had a bit of camber and toe in the front, dont know the exact measurements, that gave a more direct handling feel and turnin was alot more crisp. it was great.

just wanted to know how many of you guys are running performance v's tyresaver alignments on your daily drivers? i want to get the most out of the tyres but at the same time get some decent handling out of them also. is it an either or scenario? they are asymetrical and stagered set so i cant rotate them which sucks.

cheers.

R338OY Veteran

R338OY

Posted
Posted

I'm in the same boat mate.

My front tyres are wasted on the inside of the tread, though the rest looks like new :D

Rears wear more evenly (though completely bald :) ).

Car is sitting on coilovers and has slightly negative camber, so i'm guessing that's shortening the life of the front tread.

My mate said a camber kit will solve it (but i'm guessing handling will be poorer).

What should i do? The car is only used for street, for now, so do i need a camber kit? Or should i just save the misery of sloppier turn-in and leave it?

Abo Bob Grand Master

Abo Bob

Posted
Posted

I have the Whiteline adjustable camber bushes and adjust them all the way out for street (-1.5) and all the way out for track (-3), although I've got a slightly bent lower control arm at the moment which makes this a lie on one side until I get it fixed/replaced.

Omar, re your fronts, toe or camber can cause this. See if you can get the current settings for us. A wheel alignment shop might put it on the machine for a few $ and we can advise from there. That said, if your steering feels good then it's probably the camber which you can fix with adjustable camber bushes, providing you don't have too much to adjust out, or you can raise the car a little, or a combo of both.

Rears, there is a small amount of adjustment for camber standard but you've probably just lowered it too much so yeah, camber kit again to fix unless raising the car back up again.

R338OY Veteran

R338OY

Posted
Posted
Omar, re your fronts, toe or camber can cause this. See if you can get the current settings for us. A wheel alignment shop might put it on the machine for a few $ and we can advise from there. That said, if your steering feels good then it's probably the camber which you can fix with adjustable camber bushes, providing you don't have too much to adjust out, or you can raise the car a little, or a combo of both.

Rears, there is a small amount of adjustment for camber standard but you've probably just lowered it too much so yeah, camber kit again to fix unless raising the car back up again.

I can see by eye all the wheels lean inwards slightly. The handling is crisp too, so i'm guessing its definitely camber. I'm going for a wheel alignment & balance soon, i'll ask for their opinion on the fronts.

I'd probably get the camber bushes if that was the solution, but saying that the nose sits quite low (the front lip might exaggerate that though) so raising a few cms wouldn't be a problem to save $$ on tyres.

I'll probably post again when i get more info and see what my options are.

Thanks Abo Bob.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...