Jump to content
SAU Community

Recommended Posts

Im looking at getting RE55's on my GTR32, with the standard rims...

I know they're good on the track, but how good are they on the street? More particularly, wet/raining streets...???

Any advice/recommendations welcome :)

P.S: I noticed the sticky thread on tyre recommendations, but farked if im gonna go through 33odd pages looking for something remotely close to an answer :P

Link to comment
https://www.sau.com.au/forums/topic/198528-re55s-on-gtr32/
Share on other sites

Im looking at getting RE55's on my GTR32, with the standard rims...

I know they're good on the track, but how good are they on the street? More particularly, wet/raining streets...???

Any advice/recommendations welcome :)

P.S: I noticed the sticky thread on tyre recommendations, but farked if im gonna go through 33odd pages looking for something remotely close to an answer :P

It may be worth your while getting a second set of rims - larger ones at 9" width. Reason being that GT-R's are heavy and punish their tyres. So the extra inch or so rubber helps, albeit at a price. 255/40/17 are a good size. In any case check the load rating.

As for your second question. Yes they are driveable in the wet. But to be honest they are a noisy, harsh and offensive tyre that I wouldn't recommend running around on every day.

Link to comment
https://www.sau.com.au/forums/topic/198528-re55s-on-gtr32/#findComment-3544834
Share on other sites

Thanks for that djr81...

Im kinda hoping to not have to buy rims as that would add even more to the money i gotta dish out :P but i might have to...

The noise isnt *tooo* much of a problem as its my second car; im just wondering how it would cope if i decide to go for a burn around the block and it decided to rain on me coz they dont seem to have as much tread as a street tyre obviously....dont wanna end up sliding into the gutter lol

Link to comment
https://www.sau.com.au/forums/topic/198528-re55s-on-gtr32/#findComment-3544866
Share on other sites

pretty much any decent second hand 17X9 +20-+30 rims you buy are cheaper than just one set of 255/40/17 RE55s. so if buying the second set of rims saves you 1/3rd wear on your RE55s then that's an extra set you have every 3 sets.

and yes, once they are worn down they are pretty average in the wet. when new they are fine, but after a while they become pretty nasty. I've had wheelspin accelerating in 3rd on the road with worn semi slicks. and had a big moment. that little ring tightener was enough to convince me to use road tyres on the road, and track tyres on the track.

Link to comment
https://www.sau.com.au/forums/topic/198528-re55s-on-gtr32/#findComment-3544909
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...