Jump to content
SAU Community

Recommended Posts

Which silicone do I use to put on my coil packs to help the missfire on boost? There's a lot of different kinds, like the gasket stuff and the spray silicone, but can someone give me a picture or the name brand and which type of which one to use please? Also, is silicone the best thing to use, because I have seen posts about people using clean nail polish and heatwrap and stuff. I HAVE SEARCHED TOO!

Thanks,

Mike

Edited by Michaelove
Link to comment
https://www.sau.com.au/forums/topic/198765-about-siliconing-your-coil-packs/
Share on other sites

Selleys 401 is the one i used. Its industrial grade high temp silicone, used as an insulator, amongst other things. You can get it at bunnings.

It's probably just as important to clean the contacts on your coils, where the spring sits.

The last thing i tried was stretching each spring about 8mm longer, to make a better connection with the spark plug. I havent had a misfire since, but then the weather hasnt been freezing cold, so it may be due to that.

Edited by Munkyb0y
Selleys 401 is the one i used. Its industrial grade high temp silicone, used as an insulator, amongst other things. You can get it at bunnings.

It's probably just as important to clean the contacts on your coils, where the spring sits.

The last thing i tried was stretching each spring about 8mm longer, to make a better connection with the spark plug. I havent had a misfire since, but then the weather hasnt been freezing cold, so it may be due to that.

Thanks a lot.

no that wont work. that's more like a lubricant. get the 401. it's only $10.

Okay, the problem is that I live in USA and we don't have bunnings. Do you know of any other brands? Or any other stores I Can get it at? I don't think USA has shellys

Okay, the problem is that I live in USA and we don't have bunnings. Do you know of any other brands? Or any other stores I Can get it at? I don't think USA has shellys

what is the silicone supposed to be used for? ie, painting, flooring, ect? Is it like the caulking stuff?

Edited by Michaelove

it's used to seal glass on oven doors, and also used as an industrial electrical insulator.

not sure of an equivalent product, but there would be something.

here's the selleys 401. it's the only pic i could find

Silicone%20401%20Clear%20310g.jpg

it's used to seal glass on oven doors, and also used as an industrial electrical insulator.

not sure of an equivalent product, but there would be something.

here's the selleys 401. it's the only pic i could find

Silicone%20401%20Clear%20310g.jpg

sweet! thank's a lot man. one more question! where exactly do i put the silicone on the coil packs? that's the last thing i can't find =/

here are mine

post-29392-1198366555_thumb.jpg

seal the whole underside of the coil, up to the bracket. leave the stem uncoated, as you need to fit the rubber boot over that. also make sure you clean those contacts. u can see mine are shiny gold. they were a dull grey when i started.

here are mine

post-29392-1198366555_thumb.jpg

seal the whole underside of the coil, up to the bracket. leave the stem uncoated, as you need to fit the rubber boot over that. also make sure you clean those contacts. u can see mine are shiny gold. they were a dull grey when i started.

awesome. thank's a lot.

no worries man.

have you made sure your missfire isnt caused by your spark plugs? 0.8mm gap is highly recommended, although nissan specify 1.1mm

and many people have found the copper plugs to be better than the platinums/iridiums, that are also recommended.

Edited by Munkyb0y

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...