Jump to content
SAU Community

Recommended Posts

Hey guys, after getting a cat back exhaust in & BOV recently, i didn't know but the ppl driving behind me goes when i full throttle or even rev it hard in neutral, it gives out black smoke ONCE out the exhaust but not constantly...i think it just gives out black smoke once when i rev it high or gun it under load....

It is running rich correct? cuz i don't have a air/fuel ratio gauge, heard the black smoke was real black someone behind me said but when i revved it in neutral hard it wasn't THAT black but i dunno how it is under load... Is it even normal for the car to run rich with just a cat back exhaust (with stock cat)???? Is it normal for skylines to run rich for safety reasons???

thanks in advanced guys...

Link to comment
https://www.sau.com.au/forums/topic/199140-black-smoke-under-load~/
Share on other sites

Work out your fuel ecconomy.

Goto a servo and fill your car to the 1st click on the fuel pump

Reset your trip meter

drive about until your down to like 1/4 of a tank

go back to the same servo/pump and refil to the 1st click

look at the bowser and note down the kms

look at how many kms you have done

divide liters by kms then times that result by 100

This will give L/100kms

post that up here.

Edited by whiter31gxe

Minor correction :D

Work out your fuel ecconomy.

Goto a servo and fill your car to the 1st click on the fuel pump

Reset your trip meter

drive about until your down to like 1/4 of a tank

go back to the same servo/pump and refil to the 1st click

look at the bowser and note down the Liters

look at how many kms you have done

divide liters by kms then times that result by 100

This will give L/100kms

post that up here.

o2 sensor is not read at full load... its only used to lean out the cruise and idle maps.

Black smoke on full throttle is generally pretty normal... but the better the tune the less wasted fuel there is, if you have a stock ecu hitting rich and retard its going to do it something chronic

o2 sensor is not read at full load... its only used to lean out the cruise and idle maps.

Black smoke on full throttle is generally pretty normal... but the better the tune the less wasted fuel there is, if you have a stock ecu hitting rich and retard its going to do it something chronic

Ill work out the fuel economy...

So your saying its quite normal to run rich with black smoke under full load on stock ecu with JUST A CAT back exhaust? (With stock cat BTW)??

Edited by R33Turbo

Other ppl on the forum says my coilpacks are on the way...would that by any chance affect the reason why i have black smoke under full throtttle??

Cuz im not really happy with black smoke, worst comes to worst an aftermarket ECU would be able to tune it out right?

Also will an aftermarket ECU tune out the BOV causing the bogging??

Wat if its a SAFC?

Edited by R33Turbo
o2 sensor is not read at full load... its only used to lean out the cruise and idle maps.

Black smoke on full throttle is generally pretty normal... but the better the tune the less wasted fuel there is, if you have a stock ecu hitting rich and retard its going to do it something chronic

Simon, while this is true, the ECU will make adjustments in closed loop to maintain the correct A/F ratios under cruise, it does also have a bearing on the entire fuel map. The long term fuel trim refers to this adjustment. Fuel maps will be altered based on the amount of trimming the ECU does during normal driving to acheive correct ratio in closed loop. If long term trims are altered say 5% to the rich side, its 5% right through the entire fuel map, not just the closed loop areas. These long term trim adjustments are maintained in the ECU until such time as battery is disconnected and trims are returned to factory settings (0 or BASE). They LEARN this to compensate for alterations to things like altitude, ambient air temp and engine wear, even driving styles.

Im willing to bet you have put a venting BOV on it, put the stocker back on and 95% sure it will fix your problems and get heaps better fuel economy.

Yep i have a BOV to dump into air...So how could that affect the black smoke richness? i dun get it....i do have alot of popping sound from the exhaust which i understand if the BOV is the cause but not really the black smoke...BTW i do have coilpacks going but theres no way it'd be the cause of the black smoke under load will it??? :D

Anyway thanx heaps im worried less as skylines are supposed to run rich to be safe.

Edited by R33Turbo
Yep i have a BOV to dump into air...So how could that affect the black smoke richness? i dun get it....i do have alot of popping sound from the exhaust which i understand if the BOV is the cause but not really the black smoke...BTW i do have coilpacks going but theres no way it'd be the cause of the black smoke under load will it??? :D

Anyway thanx heaps im worried less as skylines are supposed to run rich to be safe.

If the BOV ain't leaking when WOT, it wont effect it.

Rich still inst all that much fun. Over doing it can leave glowing carbon deposits over time. Recommend grabbing something and trimming it out

" black smoke ONCE out the exhaust but not constantly" Im a bit confused as to when it is blowing smoke. A venting BOV will blow black smoke and make it run rich on gearchanges, as the ECU thinks that air coming out the BOV is going through the motor, so it adds the corresponding amount of fuel. When you change gears it fuels the motor up, then when you accelerate again it comes out as a big puff of black smoke.

Assuming the BOV isnt leaking under boost, it wont make the car blow smoke continuously when under load, just the big puff after a gearchange.

" black smoke ONCE out the exhaust but not constantly" Im a bit confused as to when it is blowing smoke. A venting BOV will blow black smoke and make it run rich on gearchanges, as the ECU thinks that air coming out the BOV is going through the motor, so it adds the corresponding amount of fuel. When you change gears it fuels the motor up, then when you accelerate again it comes out as a big puff of black smoke.

Assuming the BOV isnt leaking under boost, it wont make the car blow smoke continuously when under load, just the big puff after a gearchange.

OHHH~ i get it now... Well u know i heard it was just a big puff of black smoke when i 'double d clutch' so im assuming when i change gears after revving so high in neutral??? also in stationary ive revved it in neutral but it wasn't so much of a black smoke and it didn't seem like a big puff however there was slightly black smoke coming out as it was revved in neutral to like 6000rpm... So??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...