Jump to content
SAU Community

Recommended Posts

r33 owners will know bout this

on the rear guard theres a 25mm fin that shoots over the tire in the rear guard, i need to delete this or bend it 45deg up cause its sliced my tires.

what to do, can i .........

1) fold it up 45 deg with muliti's? (will that crack the paint)?

2) 4 inch grinder with a 1mm blade and slowly grind it away (if i do this slowly to keep the heat down will this work)

plz let me know which option is better..... 1 or 2

xoxo

Link to comment
https://www.sau.com.au/forums/topic/199198-r33-rear-guards/
Share on other sites

ok thats all well and good but which of my 2 options is best......

i need peoples opions plz.

neither are good

grinding will make the paint flake, bending by multigrips will also make it look like crap.

heating the panel up with a heat gun and gently massaging with a rubber mallet is better than multigrips if you must do it yourself.

best option in this thread was from user "J'z-R33" - get someone to roll them properly

Link to comment
https://www.sau.com.au/forums/topic/199198-r33-rear-guards/#findComment-3552769
Share on other sites

i grinded it today, the 1mm blade was a bit slow so i swiched to a normal grinding blade, the guard is pretty solid and it didnt shake around at all, came up perfectlyi left a 5 mm fin over the tire, and gave it a light file manualy to clean it up....

i winded the tein coilovers down a bit and the tire just pops in under the guard, went for a drive on a bumpy road and itall good.......

grinding is best

Link to comment
https://www.sau.com.au/forums/topic/199198-r33-rear-guards/#findComment-3554108
Share on other sites

  • 3 weeks later...
paint may not crack straight away, but eventually it will ive been told by several tyre and suspension fitters.

This is correct from what i've heard... sooner or later it will crack due to the pressure put on it, and you will get crack marks... i would be careful and only proceed if you're after a quick fix. otherwise, get a widebody full kit.

Link to comment
https://www.sau.com.au/forums/topic/199198-r33-rear-guards/#findComment-3587860
Share on other sites

Just so you know whoever you are grinding your guards.. You'll need to paint them asap because it will rust, rust will travel and ur car will start peeling and bubbling the paint..

1. Will look like SHIT

2. will degrade the car and its value

3. will reduce the structure strength of the vehicle (but you've already achived this)

So i Suggest you get a paint pen, some masking tape and mask up your exterior paint and then with the paint pen cover the open metal, Spray will prob work better but it will prob cover your exterior.

Seriously get it done.

Edited by DECIM8
Link to comment
https://www.sau.com.au/forums/topic/199198-r33-rear-guards/#findComment-3588077
Share on other sites

This is correct from what i've heard... sooner or later it will crack due to the pressure put on it, and you will get crack marks... i would be careful and only proceed if you're after a quick fix. otherwise, get a widebody full kit.

lol

from a quick lip rolling to " widebody full kit"

i have a car that had its guards rolled about 8 years ago now, no cracking, and they are not rusting

Link to comment
https://www.sau.com.au/forums/topic/199198-r33-rear-guards/#findComment-3588599
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...