Jump to content
SAU Community

What Oil Filter To Use With Hks Oil Cooler Kit?

Kaido_RR

By Kaido_RR,
in Engines & Forced Induction

 Share

Recommended Posts

Kaido_RR Grand Master

Kaido_RR

Posted
Posted

Hi,

I'm after some information about what oil filter to use with the hks type r oil cooler kit, which comes with a remote oil filter mount. As the stock oil filter looks to large to screw into the remote mount. also the length of the stock oil filter looks to large, ATM there is some j-spec brand oil filter on it which looks very small in width and length.

any help would be great :)

Cheers Michael

Duncan Grand Master

Duncan

Posted
Posted

yeah its 442. same thread but smaller (shorter) than the standard one. 442 is a generic part# most places will have one from some brand on the shelf.

http://www.fsafilters.com.au/html/passenger/nissan.html

Kaido_RR Grand Master

Kaido_RR

Posted
  • Author
Posted (edited)
yeah its 442. same thread but smaller (shorter) than the standard one. 442 is a generic part# most places will have one from some brand on the shelf.

http://www.fsafilters.com.au/html/passenger/nissan.html

so what car is it from? and can i get one from nissan? don't like generic oil filters prefer geniune nissan filter

Edited by [Michael]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...