Jump to content
SAU Community

Recommended Posts

Some small facts first off - r33 gtst s2 (1996) with no mods apart from apexi pod.

I recorded a video using my mobile phone so the quality isnt the greatest. Ill try to provide an explaination to help.

http://www.youtube.com/watch?v=02Cyv2CWqDU

In the video you can see that my idle is fluctuating from about 100-1000rpm. This occurs when ive been driving the car for around 5-10 minutes, or generally once its all warmed up properly. You may also notice that as the rpm fluctuates, so does the vac/boost.

About 3/4 through the video you can see me open the throttle a little bit. The following is what i deal with on the roads when driving. Say im in second and approaching a corner or roundabout and have to give way so i slow down. Its very likely that the car will completely drop off all rpm and die on me. In the video im in neutral or first with the clutch in i forget. Either way, when im in first and i start to slow down a bit after opening the thottle, its very likely that the rpm will drop off to around 0 but not actually stall completely. As seen in the video i rev it a bit, then the rpm drops to about 0 and the battery light flashes for a second but the car doesnt actually die.

Anyway, i plan to take the car to a workshop/garage this month to solve this issue however if i can do this at home id be excstatic.

After searching the forums heavily ive come to the conclusion that it may be caused by one of, or a combination of the following:

-faulty afm

-leaking i/c piping

-dirty aac valve

-faulty o2 sensor

-faulty tps

Ive read that cleaning the aac valve can do wonders; is this the type of problem i can solve by cleaning the aac valve at home? It's just that i dont have a large amount of cash to wave around so being able to fix this my self would be great.

Link to comment
https://www.sau.com.au/forums/topic/199778-is-this-idle-hunting-bad-idle/
Share on other sites

if not a factory computer, this can be caused by having the first few cells of the map unbalanced, ie on powerfc first 3x3 should be the sameish in fuel and timing, otherwise you get this sort of thing as it jumps through bouncing off different values.

if standard ecu, check your afm wiring and plug, and if all good try cleaning or getting a replacement aac valve

mine did this when rolling up to a set of traffic lights in neutral

it was the AAC valve. You can check this by temporarily disconnecting it. if ya idle doesnt fluctuate after disconnecting it, well theres ya problem

i ended up putting on a sr20 aac valve that was apperantly the same and doesnt do it anymore.

I had the exact same symptoms as you after pulling everything apart for a turbo upgrade (pulsing idle when stationary with car warmed up). In my case it turned out to be an air leak. Check all vacuum hoses connected to the crossover pipe and intake manifold for broken/split ends. Also check your Intercooler piping and make sure there are no leaks after the AFM. Definitely clean your AAC Valve regardless as many have mentioned.

Gave the AFM a good clean today, the inside was full of black shit. Gave it a clean with some electrical contact cleaner and put it back, the car seemed to run better than before. It still has a rough idle at times but its not as frequent.

Tomorrow i'll be cleaning the aac valve, hopefuly that helps.

  • 2 weeks later...
In the video you can see that my idle is fluctuating from about 100-1000rpm. This occurs when ive been driving the car for around 5-10 minutes, or generally once its all warmed up properly. You may also notice that as the rpm fluctuates, so does the vac/boost.

I have the same thing. At first I thought it was a Vacuum leak, but after testing with soapy water and listening with a hose I found nothing. Now I suspect it is a faulty O2 Sensor. When the car starts idle hunting try disconnecting your O2 Sensor and wait around 30seconds. When I did this my idle stopped still at 900rpm.

My theory is that the car runs fine until the O2 Sensor is warmed to operating temperature as the ECU ignores this reading until that time. Once the O2 sensor is operating, the ECU reads a false value and idle struggles as the O2 Sensor is not able to keep the ECU up to date with accurate readings. I tested my O2 Sensor at operating temp with a multimeter and noticed that it does not vary in voltage as it should. I am going to test another O2 Sensor. Will let you know how it goes.

Very interesting theory. Last week i gave my aac valve a very good clean. At first it seemed like the problem disappeared but after about 30min of driving it happened but only to a small extent. No where near as bad as it was before. The aac valve cleaning definately helped.

Unfortunately, i havent been able to drive my car enough to see if the problem has gotten any better. I got busted driving it last week and got 2 fines, one for it being manual and the other for high powered vehicle (im a p-plater). Its my second car and i drive it like once a week but i dont feel like risking more fines. Im fully licensed next month though.

The o2 sensor stuff sounds like its worth a try if it happens to me again, ill keep it in mind.

thats how my car was running when i took the BOV off and turned it on LOL

so definately check for leaks in all piping such as vacuum and intercooler/intake side of things

but as others have mentioned before try someone afm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...