Jump to content
SAU Community

Recommended Posts

Make: Nissan

Model: Silvia Q's

Engine: Blacktop SR20DET

Milage: 163,000 on dash, 98,000 in front cut

Transmission: 5 speed manual

Colour: bayside blue

Location: sydney, nsw

Complied? yes

RWC supplied? yes

Currently registered? yes, expires october 2008

Price: $15,500

Contact: 0407 931 097

Comments / Modifications:

Alot of time and money has gone into this car to make it a tough street car that is capable of circuit racing, but I'm in a bit of a situation where I think I'm going to have to sell it. Below is a list of the details:

Suspension/handling

- 16inch lightweight Intermilano wheels (sounds like they're italian but actually made in Japan)

- 5 stud conversion using s14 front/rear hubs

- R33 Skyline Front calipers and rotors, brake master cylinder and rotors

- Front and rear cusco strut braces

- Tein superstreet coilovers

- Nonathane front castor rods bushes

Engine:

- Blacktop sr20det from 1995 180sx

- Serviced head with new valve exhaust valve guides

- Tomei metal head gasket

- Tomei Rocker Arm stoppers

- HKS Step 1 cams, 256 intake and 264 exhaust

- GT28R turbo with upgraded wastegate actuator

- Z32 AFM with stainless steel intake pipe

- R32 GTR Front mount intercooler

- 3 inch straight thru exhaust with stainless steel hi-flow cat

- GFB plumback BOV

- Apexi Power FC with Hand controller

- Turbosmart boost controller

- Nismo 550cc injectors

- Walbro 500hp fuel pump

- B & M oil cooler

Interior:

- R32 GTR seats

- Pioneer MP3 player

- Greddy Boost, oil temp and oil pressure gauges

Body:

- Resprayed in Bayside Blue 5 months ago

- GTR style Front grille

- tinted windows

Car was tuned by CRD and made 204rwkw @ 16psi. Expecting it to make between 210-215 at 18psi. Will be going back in two weeks to CRD to retune it with the new wastegate actuator and more boost as my old actuator was not holding boost above 15-16psi. For those interested in the car, you're more than welcome to come see the car on the dyno if you like.

I have all receipts for all the work done and will provide these to the buyer.

post-6485-1199966114_thumb.jpg

post-6485-1199966149_thumb.jpg

post-6485-1199966188_thumb.jpg

post-6485-1199966289_thumb.jpg

post-6485-1199966350_thumb.jpg

post-6485-1199966530_thumb.jpg

post-6485-1199966563_thumb.jpg

post-6485-1199966592_thumb.jpg

Edited by Demon
Link to comment
https://www.sau.com.au/forums/topic/200771-1990-nissan-silvia-blacktop-sr20det/
Share on other sites

  • 3 weeks later...
  • 1 month later...
  • 3 weeks later...
  • 2 weeks later...
  • 5 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...