Jump to content
SAU Community

Recommended Posts

this one is i have taken from sydneykid in the coilovers thread. we got to talking swaybars.

Thanks for the advice Gary. Atm im on a full whiteline stabiliser bar kit with urethane bush set, camber front and rear and pineapples set to standard.

the front adj blades on the swaybar im pretty sure though i could only get set up at 2nd and 3rd hole. can the front swaybars be adjusted any further? how can i do it? the rear is at full hard.

What size bars are you using? My guess is the off the shelf 24 mm front and 22 mm rear, which is too narrow an adjusment range for the track work you are doing, grip or drift. You should really be looking at 26 or 27 mm front and 24 or 26 mm rear. I don't recall what model it is, if it's an R32 then you need 4 adjustment settings on the front and 3 on the rear, standard (off the shelf) is 3 front and 2 rear. If it's an R33/34 then you need 6 adjustment settings on the front and 3 on the rear, standard (off the shelf) is 5 front and 2 rear.

You should also be using spherical bearing links on the bars to give you the instantaneous effect, plus increase the feel as you need as little dampening of the response for track work. They will need regular replacement, even the Whiteline greasable and dust covered ones. Just like brake pads they will wear out, they are a consumable after all.

To give some adjustment for the usage patterns that you have, you can't run spring rates that high, anything much over 5 kg/mm front and 4 kg/mm rear will negate the effect of any adjustment (bars, shocks or geometry) that you do. Use the bars to control the roll, that's their job after all and then adjust the rear subframe geometry to suite the traction requirements. At the moment you have nothing to adjust that will help with your problems.

Cheers

Gary

Somethings to think about;

You would need to use twice the spring rate to achieve the same anti roll as a stabiliser bar. Why? Because the inside wheel goes down the same amount that the outside wheel goes up. So a stabiliser bar has twice the movement for the same amount of roll as a spring, hence twice the amount of resistence to roll. Only the outside spring resists the roll, the inside spring does nothing.

When you are not going around a corner, the stabiliser bar does nothing, so you get more traction from the softer spring rate.

Stabiliser bars are easily adjustable, spring rates are not. If, on any given day, you need more or less front or rear anti roll you can't easily, quickly or cheaply adjust it with springs. That's why (when the regs allow) race cars have driver adjustable stabiliser bars.

Diagonal weight transfer is best resisted with anti roll, not spring rate. Under corner exit acceleration the outside rear tyres take a large amount of weight transfer, this manifests itself as lift to the inside front tyre. Reducing inside front tyre grip means that the outsdie front tyre is carrying more of the cornering load than would eb the case if the diagonal weight transfer was a resisted by a stabiliser bar. Excessive outside tyre wear and inability to maintain consistent lap speed due to overheating are all systems.

Too little anti roll has side effects. One of which is the need to run excessive amounts of camber, front and/or rear. This reduces the contact patch of the tyre for straight line acceleration and braking.

Running an excessively high spring rate becuase of a lack of antir roll has a few more side effects. One of which is the need to run excessively high rebound damping in the shock absorber to control that higher spring rate. This means the shocks resists (slows down) the downwards movement of the suspension and makes it more difficult to keep the tyre in contact with the road surface. Skipping from small bump to small bump is not good for traction.

I have several more pages in me if necessary, if anyone remains unconvinced.

Cheers

Gary

Selby's swaybars (not sure if they make swaybars for Skylines) -

http://www.hotfrog.com.au/Companies/Selbys-Swaybars

K-MAC swaybars (As far as I know the prices on the website are in US dollars

and they make swaybars for R32, R33, R34 in non adjustable and adjustable).

K-MAC website -

http://www.k-mac.com.au/

Swaybar prices -

http://www.k-mac.com.au/pages/tuning/listofkits.htm

Also I noticed they can custom make springs.

Edited by SKYPER
Selby's swaybars (not sure if they make swaybars for Skylines) -

http://www.hotfrog.com.au/Companies/Selbys-Swaybars

K-MAC swaybars (As far as I know the prices on the website are in US dollars

and they make swaybars for R32, R33, R34 in non adjustable and adjustable).

K-MAC website -

http://www.k-mac.com.au/

Swaybar prices -

http://www.k-mac.com.au/pages/tuning/listofkits.htm

Also I noticed they can custom make springs.

I thought Selbys was Whiteline?

Anyway thanks for the info and links .

they are hollow bars.

size f: 24.2mm

size r: 27.3mm

i use the gtr spec ones but they bolt onto my gts fine

gts spec ones are

f: 27.2mm

r: 23.0mm

Where did you snap these up from and how much did they set you back???

they are hollow bars.

size f: 24.2mm

size r: 27.3mm

i use the gtr spec ones but they bolt onto my gts fine

gts spec ones are

f: 27.2mm

r: 23.0mm

Front GTR (4wd) bar won't fit a GTST (2wd), plus it is too soft a rate.

Cheers

Gary

Gary,

I have forgotten....what are the size of the sway bars in the GB that I have? :P

From memory, 24 mm solid front adjustable and 22 mm solid rear adjustable.

Minimum adjustment is equivalent to a 27 mm hollow bar, with 6 steps of around 8% increase each on the front.

The rear is equivalent to a 24 mm hollow bar, with 3 steps of around 12% increase each on the front.

All the Jap hollow bars I have tried are grossly underdone. As an example, we swapped John's 300ZX hollow bars for some solid bars, backed off the spring rates a bit and it was 1.5 seconds a lap faster at Philip Island.

Cheers

Gary

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...