Jump to content
SAU Community

Recommended Posts

Hey guys got my front pipe today its for a R33 GTST just wondering, i called up an exhaust place they said i need a dump pipe and i got confused... Does that mean i cant connect it because i need this dump pipe thing? this is from my stock turbo , The parts i got now is a Greddy/Trust power extreme II catback system + the front pipe . Also whats the diffrence between split dump pipe to my front dump pipe? is the other better or mine.. for more power gaines because my aim is to get a bit more power... from my stock turbo..

trustdownpipelrgxe5.th.gif

Edited by geraus
Link to comment
https://www.sau.com.au/forums/topic/200829-got-my-greddytrust-front-pipe/
Share on other sites

CES makes a good split dump-front pipe. since you'd already got the front pipe, I'd go for a tomie dump pipe. You can get a hks dump which has a split for the wastegate but do a search here for comments. some say the split joins back too close and causes turbulant hence defeats the purpose.

Hey thanks so much! Sorry where is CES? is it on the NS fourms? and yeh thats what im after! The dump pipe to connect to my front pipe, Whats the diffrence between the split? just wanted to make sure everything is ok! im just a little bit worried thats all, i thought i brought the wrong front pipe.

Thanks

Geraus.

that front pipe should connect to your standard dump pipe or else they couldnt sell them as a bolt on for r33 gtst's kinda defeats the purpose.. i;m pretty sure greddy make dumps for the rb25 i know they dont for the rb20s and im possitive they do for sr20 so just go2 ur auto barn or nengun or where ever u got it from n check it out those hks ones would be ok but the ces and batmbl ones are the best bcoz the wastegate pipe goes right down into the front pipe but considering you've already got the greddy front pipe u might as well keep it and get some type of split dump pipe when u want...

but i dont think u need it straight away that greddy front pipe should bolt up to ur standard dump pipe no worries and neways u could easily do it urself mate its not had 5 bolts and some gasket glu n ur away!!

Edited by gt-t_r34

Hmmm so do i need is the dump pipe? And yeh im getting a high flow cat... from boss imports.. would you guys know if he sells the dump pipe that i need?

Thanks so much all of you's for the replys.. thanks

Edited by geraus

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes. Probably, given that there is only access from the bottom end of it, go with a drill bit. Don't start too small. 7 or 8mm is probably the right size. You want something that can make a big enough hole to do some damage, but not so bit that it clashes with the steel or binds up and breaks your wrist. A slow speed is probably a good idea too. Once the rubber is destroyed, you then have to get the crush tube off the stud, which will be the whole heat/oil/cutting exercise all over again, but this time with the need to strictly avoid damaging the stud (any further than the corrosion might already have done.
    • We replaced the connector just because we could and it was still there, once we swapped the injectors around it stopped. The injectors were something I had thoughts of replacing even before I first started the engine and in hindsight I should have 
    • Not too sure just yet, want to have a go at doing what I can myself, but to start with want someone to cast their eye over it tell me what needs doing to get it running and back on the road, so anyone with great overall knowledge would be ideal.
    • I personally would go with cutting out the rubber. Then deal with getting sleeve off separately. Rubber can be painful to cut, it loves to jam up cutting tools. I normally have success with drill bits, deburr bits, angle grinders, jigsaw, reciprocating saw, and never forget... fire. Obviously different tools won't work in all locations you're trying to work with, and you need to be comfortable with each. You personally may be happy slowly slicing it out with a razor blade, if you are, go for it with one too! Feel free to wait for others to weigh in also on their thoughts.
    • So ... I got everything disconnected and started dropping the frame. Three of the four mounts started to come down but the fourth one (the one with the nut that gave me all the trouble) won't budge. The inner metal sleeve stays up tight against the chassis rail although the outer part of the mount drops a bit (and can be levered quite a lot more) but it's just stretching the rubber bushing. So I reckon there's some serious corrosion inside the inner sleeve and holding it tight to the lug at the top of the bolt. Tried everything I can think of so far: penetrating oil, whacking the top of the sleeve to vibrate it and wedge a screwdriver blade in there. I also tried to turn the inner sleeve a bit by hitting it with a chisel at the bottom. It's stuck solid. What do you think about cutting the rubber with a blade so I can drop the subframe around it anyway. Then worry about getting the inner sleeve off after? Will that work? Is it gonna give me even more problems?
×
×
  • Create New...