Jump to content
SAU Community

Recommended Posts

just asking people on there thoughts of having a stagea as vehicle to tow, i know i used my r33 gtst to tow my mates skyline to mechanics when he broke down and afterwards it took me about 1/2 hour of constant thrashin to get my car back to normal damm learning computers ;)

question is stageas and towing car trailers with cars on it ie a 33 or similar wieght any good or am i just damaging a nice vehicle like the stagea

Link to comment
https://www.sau.com.au/forums/topic/200959-stagea-towing/
Share on other sites

have a look at this thread http://www.skylinesaustralia.com/forums/To...html&st=100

even if you get the 2000kg towbar that doesn't leave much capacity after the trailer. my trailer weighs 540kg and is considered light. most rental car trailers weigh 7-800kg, leaving only 1200-1300kg for the car you're towing. not many stripped out race skylines weigh in at that, let alone road cars.

4WDs are the best (ie safest) things to tow with. If you are going to be towing car regularly, you should consider gettng a more suitable tow vehicle. My old GQ Patrol is rated to 3500kg towing capacity braked, as are most heavy 4WDs. lighter things like Hilux, Navara, Pajero etc are usually in the 2000-2500kg range. A diesel 4WD will also return much better fuel economy figures than a Stagea too. My diesel GQ gets 14l/100km towing - about what a Stagea gets just hauling itself around!

Link to comment
https://www.sau.com.au/forums/topic/200959-stagea-towing/#findComment-3574054
Share on other sites

Your car needed to be thrashed? There is no learning in the stock ECU, the only thing is the low octane map if they detonate heavily, and that only resets when you turn the car off

adriano after towing the car for 20 mins , being an auto too (not sure if thatmade a difference) for a bit of time afterwards whenever you accelerated it would be slow to respond and the power output felt restricted ie you know when your missing a few g's a bit of constant foot to the slow soon leveled that out

and corect me if im wrong but doesn't the standard ecu have a learning system to it, from research i though it held up to the last 50 times you drove and setup the vehicle as so, so if you were a grandma driver it would give nice slow gear changes slower acceleration and better fuel eco, or if you thrashed it better response more fuel, not a huge difference in the vehicle however just slight

Link to comment
https://www.sau.com.au/forums/topic/200959-stagea-towing/#findComment-3575534
Share on other sites

adriano after towing the car for 20 mins , being an auto too (not sure if thatmade a difference) for a bit of time afterwards whenever you accelerated it would be slow to respond and the power output felt restricted ie you know when your missing a few g's a bit of constant foot to the slow soon leveled that out

and corect me if im wrong but doesn't the standard ecu have a learning system to it, from research i though it held up to the last 50 times you drove and setup the vehicle as so, so if you were a grandma driver it would give nice slow gear changes slower acceleration and better fuel eco, or if you thrashed it better response more fuel, not a huge difference in the vehicle however just slight

I've always thought cars do a bit of this although I dont think the logic is as complex as you might wish.

It'd just have a few different settings it could use depending on your driving style, things like different shift points etc. for the auto.

Can anyone confirm (someone that knows what they're talking about, not like me) ?

Link to comment
https://www.sau.com.au/forums/topic/200959-stagea-towing/#findComment-3575830
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I didn't know about induction heaters but checked them out and they look awesome but too pricey for the occasional job like this. And I'm too nervous to take a flame anywhere near there as the petrol tank is so close, although I was intrigued with the crayons suggestion 😁 I filled a coke bottle lid with penetrating fluid and raised it on the jack so the nut was submerged in it all night. Then went in with a tiny cold chisel and got it almost to the point of splitting but not quite (I didn't want to damage the bolt threads). Then I hammered a socket back on and gently worked it until I felt movement. And it's off 😀
    • I should. But it already uses too much fuel for a daily. You might note my recco for engine chnages are almost exclusively to people who have it as a weekender/summer car. I don't even have room to keep the spares for this one, let alone another car.
    • If I had "perfect R33 GTR" kinda money I would have bought one of the crazy expensive low mileage HJA cars, but I am sadly not that wealthy. I already picked this car out of various Skylines for sale locally, most of which were worse in some way. Only a few cars were actually better but also more expensive. In terms of buying a motor locally, I at least have the option to inspect it myself and juding the seller as a person, and used or freshly rebuilt engines that some people sell are actually ok price-wise. I knew the car was going to require work, but shit piled up real fast and I haven't even driven 1000km yet as the turbo started oiling like a bitch within a few weeks after I got the car.   I assume it wasn't actually me who cracked it, though there is no way to know when that crack formed and if the previous owner even knew it was there. Buying another 05U Block can be a gamble, yeah, but the cheapest PRP cast block is like twice or more money-wise, and billet is 3 or 3 times as much. For now I am most likely just keeping the current engine, as a rebuild or engine swap isn't happening right now. But I am seriously considering buying a second engine and selling mine in return. Might be a sweet deal at the end.
    • Hi all. I need some help buying the correct size banjo bolts for my 2860 turbos. Because whoever installed them tore up the original part, I ordered new ones of this kind, because I just figured these were the most leak-resistant option as I already had trouble with a shitty braided line. I need to know the thread size of the smaller left hole, that is the turbo oil feed connection. I found out so far that the turbo oil inlet apparently has a 7/16"-24 thread, but I cannot find any listing or description of the thread size on this line. I do not have the original bolts. I tried using the bolts that were in the turbos (the ones that were mounted with the shitty braided line) but they sit very loosely so they can't be the right thread. Means either these bolts are the wrong ones (how do they fit the turbo then? no clue) or the wraparound-lines have a different thread than the turbo oil feed itself. Help is appreciated, asking Nissan directly is obviously not going to work.
×
×
  • Create New...