Jump to content
SAU Community

Recommended Posts

  • Replies 607
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Maybe we should do ice skating before it gets too cold.

Jay did you buy the EVO ones like talking to brad about??

Yeah picked them up today :bomb_ie:

Need some bits for them but so I'm gonna talk to Brad tomorrow about it.

nice jay i saw you in that thread and left them for you. muppet

alas i wont have money for those outlaws til the end of the month :bomb_ie: hope they are still floating around, I need something by next track day. now that joey and i have our cams, its on like donkey kong!

i get two decent stops in currently, then its all noise til they cool down. same as in the olden days. fun fun fun

all compliance stuff

ehehhehe <peter griffin laugh>

looking at fluid change, bigger fronts and some rotors+pads on the rear. i figure i may as well go bigger rather than just new rotors and pads all round, although that will be an obvious improvement i will probably end up going bigger eventually anyhoo.

So ice skating??? I'm sure Brads going to love this! :)

It's been ages since I have been and might have to bring a pillow and some race tape :thumbsup:

Is there a ice rink close?? I have no idea for campbelltown

I say saturday night and can have dinner as well??

For June how about we go to the movies cause "speedracer" is coming out on June 20th :)

July do skidpan if Dave has given us prices and dates by Start of June.......

Jess, i'm in for ice skating :D

The closest one for you guys is liverpool

http://www.lccfss.com.au/

or, Macquarie

http://www.macquarieicerink.com.au/

Cheers Albert :P Should we do this in the day or night peeps? I prefer night and have dinner after....

Will check them out and see which one is nicest...Has anyone been to these before??

i may make it to this one if its held on the right weekend i wont be in sydney on 24/25th but w/e either will be good... and ill be there with a extra turbo this time and in silver :banana: i hope thats enough of a hint for some people who paid attention at the last meet.

can't wait

iceskating ftw

Livepool ice rink has "Ice Disco" Saturday nights , could be cool :P

http://www.lccfss.com.au/timetable.html

http://www.lccfss.com.au/Location.html

http://www.liverpoolcatholic.com.au/

we can have dinner there as well

I think Macquarie is a bit to far for us to travel?? What does everyone else think...

The first post will be updated sunday night looking at the 31/5/08 Saturday??




  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...