Jump to content
SAU Community

Recommended Posts

Item:

Neo RB25

* Garrett GT35/45 Turbo with custom heat sheild

* 6BOOST hi-mount Manifold

* 48mm wastegate

* Bosch 750cc injectors

* Fuel Regulator

* Eagle 8mm leads

* 4inch Dump pipe

* Screamer pipe

Location:

Toowoomba

Item Condition:

Perfect condition only got bout 40000km on the motor

Reason for Selling:

no longer needed

Price and Payment Conditions:

$5000 ono

Extra Info:

I had this motor in a vn commodore

Built By Steve at Superb Mechanical

Tuned by matty Spry at P.I.T.S.

Makes 441hp

Runs 10.66 @128mph down the 1/4 mile but there was definatly room for some improvement

Pictures:

MyVNCommy.jpg

PowercruiseDyno.jpg

Drags1066.jpg

Edited by 57QCK
Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/
Share on other sites

so thats just a bolt in rite, my cousin has an r33 gtst and he is lookin for a motor because he has fried a piston, so what will we need to get this motor running, eg computer and other stuff, plet me know, may be intersted

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3582821
Share on other sites

:)

only if i had thing money.. 10 sec neo, very nice..

free bump

10sec motor in a VN Commodore, probably running auto with trans brake, stally etc

Won't be a 10sec setup in a skyline, but either way good value for money!

Good luck with the sale.

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3583074
Share on other sites

10sec motor in a VN Commodore, probably running auto with trans brake, stally etc

Won't be a 10sec setup in a skyline, but either way good value for money!

Good luck with the sale.

yeah buddy usin a auto with transbake but dont c why it wouldn't be a 10sec setup in a skyline as they r bout the same weight as a vn

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3585468
Share on other sites

try getting a 10 second pass using a manual then you'll see why.

and i would think vn's are a fair bit lighter than r33/r34's.

r32's might be around the same weight, but you would still struggle to get a 10 second pass with a manual.

good luck selling bud.

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3585613
Share on other sites

hey mate i got a mate that has a dato sunny with a sr20det and manual and he pulls consistant 10sec passes he is now building a gsr lancer with evo 6 motor i think

nice set up good luck with the sale

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3586414
Share on other sites

err..point of that last post?

...anyways considered selling a complete setup ie engine, loom and computer? obviously the motor may be capable of running 10's but without the tune it wont really do anything. youre making good power from an interenally stock motor!

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3586923
Share on other sites

nice.... 400+ hp on stock internals... is it alryt????

my rb25det is running low compression. so was thinking to rebuild it to handle more power and maybe a bigger turbo....

but didnt have enough money for all that....

if this motor will give that hp in my r34. and last long........ is this a ryt chice guys?????

how much money im looking on the top to put this motor in.

i got a Hsk pro ecu... maybe i can use that for this one...

anyone got any suuggestions please....

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3591843
Share on other sites

nice.... 400+ hp on stock internals... is it alryt????

my rb25det is running low compression. so was thinking to rebuild it to handle more power and maybe a bigger turbo....

but didnt have enough money for all that....

if this motor will give that hp in my r34. and last long........ is this a ryt chice guys?????

how much money im looking on the top to put this motor in.

i got a Hsk pro ecu... maybe i can use that for this one...

anyone got any suuggestions please....

it is fine to run that power as im usin a 50/50 toluene/bp ultimate fuel mix and it was tuned by matty spry. if you've got a 34 then your gearbox should be fine and u can use that ecu, all you'll need to do is bolt it in and get it tuned. the motor is still in my car and running if u want to see and hear it running.

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3591999
Share on other sites

how much boost was that power level made at ? its prity impressive on standard internals great luck with the sale mate, if this came by a month ago i woulda grabed it and put some forged rb30 botom on it :) but iv already got all the parts i need apart from the rb30 block :(

good luck with the sale "very good price for the power level" not sure how long itll last on standard internals and im prity sure this will make around mid 11s on a r34 skyline if you could get grip or even a lil lower..

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3592003
Share on other sites

oh ok.... some ppl say it wont last long with this internals......is it true?

correct me if im wrong.

i live in melbourne. where is ur place?

well i've had it running for bout 1 1/2 years and never had a problem with it, it all depends on who tunes it and running the fuel mix helps and its always been looked after properly. i live near brisbane.

Link to comment
https://www.sau.com.au/forums/topic/201606-neo-rb25-motor/#findComment-3593025
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...