Jump to content
SAU Community

Importin A R34 Gtr

R34GTTSKY

By R34GTTSKY,
in Western Australia

 Share

Recommended Posts

R34GTTSKY Experienced

R34GTTSKY

Posted
Posted

hey guys

need peoples opinion. i'm looking at importing a R34 GTR later on and wanna know is it better to import it privately from japan myself or wether i should go thru a company?

i've heard both good n bad things that could happen to both sides of import it privately or thru company.

also is it hard to fish around for a bayside blue coloured gtr?

Link to comment
https://www.sau.com.au/forums/topic/201711-importin-a-r34-gtr/
Share on other sites
sidewayssam Mentor

sidewayssam

Posted
Posted

i think that you should go through a company if you arent viewing it first, companies like imports101 have people in japan who inspect the veichles before you purchase them, importing privatly you might receive a car that has had the odometer wound back excessively and been in previous accident. plus if you go through and import place you should get warranty, do you know if there is much price difference from privatly importing or through a company?

Dani Boi Grand Master

Dani Boi

Posted
Posted

You cant wind back digital displayed km unless you swap the dash I think and there arent may GTR 34's around so I think you'll find most later GTR's have genuine km...perhaps. Personally I dont think I could buy a car thats worth $50k plus and not even look at it

Stage2 Collaborator

Stage2

Posted
Posted

Got my car through www.j-spec.com.au and Ben Lippa sorts out everything for ya! Just sit back and relax and wait for your phone to ring ALOT!!

But for 1k, he does alot of work for you.... all paperwork, inspection reports etc... pretty much everything to get you through the whole process... negative side.. took 3months to arrive at docks from payment date!!

No regrets though!!!

SkyDragon Community Regular

SkyDragon

Posted
Posted

For the record digital dashes can be altered. It was notorious in the Toyota Soarers. Apparently you can connect to them via a laptop and reset the display! These were hard to detect for auctioneers, only bad reinserting of dash and console left behind evidence of tampering. As for the R34, not sure?

R34GTTSKY Experienced

R34GTTSKY

Posted
  • Author
Posted
Even iron chef imports he is a top bloke and goes over to japan everynow and then and hand picks the cars himself.

http://ironchefimports.com/site/

pretty cheap broker fee aswell :D

i'll have a look thanks wes=)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I agree with everything else, except (and I'm rethinking this as it wasn't setup how my brain first though) if the sensor is at the end of a hose which is how it has been recommended to isolate it from vibrations, then if that line had a small hole in, I could foresee potentially (not a fluid dynamic specialist) the ability for it to see a lower pressure at the sensor. But thinking through, said sensor was in the actual block, HOWEVER it was also the sensor itself that broke, so oil pressure may not have been fully reaching the sensor still. So I'm still in my same theory.   However, I 100% would be saying COOL THE OIL DOWN if it's at 125c. That would be an epic concern of mine.   Im now thinking as you did Brad that the knock detection is likely due to the bearings giving a bit more noise as pressure dropped away. Kinkstah, drop your oil, and get a sample of it (as you're draining it) and send it off for analysis.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I myself AM TOTALLY UNPREPARED TO BELIEVE that the load is higher on the track than on the dyno. If it is not happening on the dyno, I cannot see it happening on the track. The difference you are seeing is because it is hot on the track, and I am pretty sure your tuner is not belting the crap out of it on teh dyno when it starts to get hot. The only way that being hot on the track can lead to real ping, that I can think of, is if you are getting more oil (from mist in the inlet tract, or going up past the oil control rings) reducing the effective octane rating of the fuel and causing ping that way. Yeah, nah. Look at this graph which I will helpfully show you zoomed back in. As an engineer, I look at the difference in viscocity at (in your case, 125°C) and say "they're all the same number". Even though those lines are not completely collapsed down onto each other, the oil grades you are talking about (40, 50 and 60) are teh top three lines (150, 220 and 320) and as far as I am concerned, there is not enough difference between them at that temperature to be meaningful. The viscosity of 60 at 125°C is teh same as 40 at 100°C. You should not operate it under high load at high temperature. That is purely because the only way they can achieve their emissions numbers is with thin-arse oil in it, so they have to tell you to put thin oil in it for the street. They know that no-one can drive the car & engine hard enough on the street to reach the operating regime that demands the actual correct oil that the engine needs on the track. And so they tell you to put that oil in for the track. Find a way to get more air into it, or, more likely, out of it. Or add a water spray for when it's hot. Or something.   As to the leak --- a small leak that cannot cause near catastrophic volume loss in a few seconds cannot cause a low pressure condition in the engine. If the leak is large enough to drop oil pressure, then you will only get one or two shots at it before the sump is drained.
    • GTSBoy
      Help! Leak coming under transmission

      By GTSBoy · Posted

      So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
×
×
  • Create New...