Jump to content
SAU Community

Recommended Posts

Hey,

Just wanna say when you change your coolant and bleed it off wash your car straight after bleeding it off. I could see the coolant going on my engine from bleeding it off but didnt realise it was blowing onto the passenger side of my car on a very hot sunny day.

I drove to tafe and back home to realise i had alot of little dots of it on my car and it was too late to wash it off, i almost cried :D . So i wanna warn you guys so you dont experience such painful emotions for no reason and almost cry like me.

Edited by WET-25T
Link to comment
https://www.sau.com.au/forums/topic/204123-coolant-can-make-you-cry/
Share on other sites

Hey,

Just wanna say when you change your coolant and bleed it off wash your car straight after bleeding it off. I could see the coolant going on my engine from bleeding it off but didnt realise it was blowing onto the passenger side of my car on a very hot sunny day.

I drove to tafe and back home to realise i had alot of little dots of it on my car and it was too late to wash it off, i almost cried :D . So i wanna warn you guys so you dont experience such painful emotions for no reason and almost cry like me.

damn...... thanks man

if it wont wash off try using a light cutting compound or cream, then polish afterwards, should get it off, it would only stain the clear coat, just make sure its a light cutting cream or a pre polish cream/compound.

Edited by 4drftn

LOL thanks guys i didnt even think to ask for hints or tips to get it off. Its been a few days now however.

I was thinking how to prevent it and all i can come up with is putting like a jar or ice cream container over the bleeder screw. I used my hand for a bit but it gets really hot.

Radiator fluid also doesn't taste very good. Its quite tangy..... true story.

haha comes to me as something Ralph Wiggum would say...."Ms Hoover, I have no coolant left", "Why Ralph, blown head gasket?", "No, I drank it all, it doesn't taste very good". I crack myself up sometimes...hehe.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
    • Mine is all -12, I’m running a dry sump in a billet block though 
    • HG's high flow is not "bolt on". The core is shorter, moves the comp cover rearwards in the engine bay. means you have to deal with the inlet plumbing a little bit. This is probably something to consider with every "bolt on" turbo anyway.
×
×
  • Create New...