Jump to content
SAU Community

Recommended Posts

  • Replies 487
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Again can everyone that is wanting to stay overnight please visit the Accommodation thread and post your interest as I would like to book rooms on Monday 9th of June

http://www.skylinesaustralia.com/forums/Au...on-t220995.html

Stayed @ a B&B about 20kms from Yass...

Chose to take the dirt roads.. They'd just done something to the roads to let the water through and it was bumpy as f*ck!

Good fun though :D Pictures will follow soon haha..

Oh yeah, it was so bumpy the front number plate rattled off...

Stayed @ a B&B about 20kms from Yass...

Chose to take the dirt roads.. They'd just done something to the roads to let the water through and it was bumpy as f*ck!

Good fun though :blush: Pictures will follow soon haha..

Oh yeah, it was so bumpy the front number plate rattled off...

thats how I f**ked my front bar in canberra :thumbsup: and I lost one bolt for my licence plate..

thats how I f**ked my front bar in canberra :D and I lost one bolt for my licence plate..

Haha yeah, my front bar does have a slight crack in it too from it....

Fun times though :(

Make matters worse parked outside the girlfriends house when I got back and got a $132 fine for parking not parallel to the traffic!!

Only 2 weeks left peoples!!!

Christian, can you call me when you're free to organise a time to wax-on wax-off.

Still gotta fit my front bar, put my back seat in, finish part of my boot, put my boost controller in...

How is everyone else going for time??

WORDS OF WISDOM - Don't pull out now!!! You will definately not be getting any sort of refund!!

if you're talking about the display, this is true :D

have hit a slight speedbump with the supplier of most of the gear though, so I still need to talk to him, but he's busy as a bee... and owes me money...

Any idea on how we're gonna set this up people's?

Numberplate won't be ready on time so I have one, hence I have to try and hide the front or the back as much as possible..

Pffft, just get some dodgy-looking pieces of carboard roughly the right size, and write "Traffic" on them...

Problem solved! :P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...