Jump to content
SAU Community

Fs - Rb30 Cp Pistons

[200]
 Share

Recommended Posts

[200] Mentor

[200]

Posted
Posted (edited)

I bought some pistons from the states to use in my car but seeing as they've supplied me the wrong ones I thought I might as well just sell them.

I asked for a 22mm pin diameter to suit my rods but they supplied me with a 21mm pin. I couldn't be bothered rebushing the rods to suit as I specfically asked for 22mm pin.

They are flat top pistons which will give around 8:1 comp. ratio.

86mm bore

BLACK TUNGSTEN COATED PINS - Micky Mouse pins

CPN RING SETS - Micky Mouse rings

I am asking $1200 for these which is cheaper than any sponsor. Add $20 for delivery.

Email 2001s15 at iinet.net.au or PM if interested.

Edited by [200]
Link to comment
https://www.sau.com.au/forums/topic/204981-fs-rb30-cp-pistons/
Share on other sites
[200] Mentor

[200]

Posted
  • Author
Posted

I need to get rid of these. They are just a paper weight to me.

Someone give me a reasonable offer.

Keep in mind that they are already MUCH cheaper than what anyone else would sell them at as they do have the CPN ring set and black tungsten coated pins.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • MBS206
      Most women will agree that parking is the most taxing part of driving

      By MBS206 · Posted

      It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...