Jump to content
SAU Community

Front Indicator Bulbs For R33 S2 Gts-t

POLICE

By POLICE,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

POLICE Mentor

POLICE

Posted
Posted

Hey ya'll

I've recently changed my front indicator position to where the parker lights were.

Now my problem has been finding replacement amber bulbs for the conversion.

I have used some T10s but they flash like crazy and I'm quite sure that the bulbs are T15s.

I also called most of the big autoshops but they only stock clear T15 bulbs.

Currently I've just lightly coloured the outer surface of my T15s amber, but it looks like shit.

I'd like to get some LEDs which might shine a bit brighter so it's more visible to oncoming traffic.

So if anyone has done this conversion and changed the bulbs, could you tell me where you bought them from?

Cheers

G

POLICE Mentor

POLICE

Posted
  • Author
Posted

I just re-wired the indicator to the parker position, I haven't wired the parker up to anything.

Yeah that I can do, but is there any other amber bulbs that can fit into the parker position and not flash like crazy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Slight brake pedal stutter after new pads

      By MBS206 · Posted

      Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • PranK
      Slight brake pedal stutter after new pads

      By PranK · Posted

      Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • GTSBoy
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By GTSBoy · Posted

      My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...