Jump to content
SAU Community

Recommended Posts

I put my set on today, on an R32 gtst.

Front: 18x8.5 +29 with 225/40/18

Rear: 18x9.5 +35 with 235/40/18

dsc01366copyhw6.jpg

dsc01367copyig4.jpg

Hey Aaron, i noticed you didnt put the centre caps on , i too personally would prefer a different style cap, i even tried the rays 57's caps but doesnt fit.

  • Replies 126
  • Created
  • Last Reply

Top Posters In This Topic

Had my shadow silvers fitted yesterday on my R34 GTT looks a treat , peep my gallery

got a set of rays lock nuts to keep em on.

i also fitted some anodised blue 'works' nuts which is the same company as rays right?

Hey Aaron, i noticed you didnt put the centre caps on , i too personally would prefer a different style cap, i even tried the rays 57's caps but doesnt fit.

Yeah, i think they look better with no centre caps.

What offsets did you get for your gtt?

Hi mate,

how u go with +29 offset at the fronts? rubbing the front guards?

They don't rub on anything. close to the inside end of the side skirt but no issues yet.

Are the DTM Rush Shadow Silver still available? Is it possible to get them with tyres as well?

I'm after a set of these for a Series 2 R33 GTSt, but I'm not sure on the measurements that would fit. My aim is to fill out the guards as much as possible without having to make any body modifications.

Any help will be greatly appreciated. ;)

when i ordered mine i rang them direct from their website http://www.accessauto.com.au/ & i spoke to adrian and steve...maybe they have run out of stock? that is my guess

when i ordered mine i rang them direct from their website http://www.accessauto.com.au/ & i spoke to adrian and steve...maybe they have run out of stock? that is my guess

Yeah i guess so?!

I cant see the pics either

I cant believe this, ive asked twice for the payment details, and ive sent a PM with my mobile number asking for contact, and got none.

Hi N1

Sorry if there has been an issue I replied ur PMs i dont know if there has been an issue with the PMs at all sorry for inconvienience but they have been replied. As per PMs please send email enquiries as bank details are PDF and have issues in the PM attachments for some reason or ph 03 9873 0133

i setup an account with photobucket as recommended by N1GTR!

finally...here are the pics of my gtr with 18x9.5+25 offset :teehee:

im fitting the factory side skirts as i think that the current side skirts hide the shape of the car & the 'fatness' of the new wheels!

CIMG3850.jpg

CIMG3750.jpg

Hey ive ordered these rims for my 32 gtr could someone please photo chop this car to white for me... cheers.

also Marko are these you got the shadow silver?

yes they are shadow silver - what colour u getting? they would get great on a white gtr

i have since taken off the gay centre caps - look much tougher without them

Edited by Marko R1
Hi N1

Sorry if there has been an issue I replied ur PMs i dont know if there has been an issue with the PMs at all sorry for inconvienience but they have been replied. As per PMs please send email enquiries as bank details are PDF and have issues in the PM attachments for some reason or ph 03 9873 0133

I will call after the long weekend

  • 1 month later...

Hi Guys

Now available Satin Black powder coat and ONYX Pearl (dark gunmetal) powder coat for the DTM Rush and Z7s. Rush Pictured in Satin Black and Z7 in ONYX Pearl

Satin Black additional $110 per set

ONYX Pearl additional $150 per set

allow 7-10 days for process

dtmblackdc3.jpg

z7onyxmd5.jpg




  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...