Jump to content
SAU Community

Will These Splits Fit My Car? And Which Of These Head Units Will Be The Better Option For My Setup


Recommended Posts

Hi all

I'm in the process of working out my car audio setup for my 4 Door R34 and am a bit stuck on which front speakers to buy, and also which Head Unit to get installed.

Speakers first:

At the moment the decision is between JL Audio VR600CSI Splits, or the new Alpine Type R Splits.

They will be running of a 4x60wrms Pioneer Amplifier (GM6300F). If I go the Type R splits, I will probably bridge the amp to feed them the juice and focus on the front staging as I am going for a sound quality focused install rather than just what's loud and clear.

Now the question is, will these Type R components fit in the 4 Door R34? Has anyone had any experience with these speakers and skylines?

The salesperson had concerns about the depth of the Type R speakers but said that there wouldn't be any problems with the JLs. However looking at paper specs the surface mount depth of the two speakers are the same?

I would prefer the Alpine speakers and they're also going to cost a fair amount less at the moment which means I can put the money I save towards getting my doors skinned with deadener.

As for the head unit:

I was looking at a JVC KD-AVX11 to get the in between of DVD and a good deck with 7 band Equaliser. Then I discovered that they only had one set of preouts so I disregarded that head unit.

After hearing a 3preout JVC DVD Source unit and then an Alpine equivalent, JVC is now out of the question!

So I've narrowed decision down to the following non-dvd units to focus on sound quality at an affordable price as that's what counts when you're driving and aren't watching the screen:

Pioneer DEH-P6950

Alpine CDA9885

As far as aesthetics and menu layouts etc.. go, I am leaning towards the pioneer, though I believe the Alpine to be marginally better in the sound quality. Note that the Pioneer unit has 7 band equaliser.

Any experience, suggestions, advice on which way I should perhaps go with my head unit suggestion will be taken into consideration. Both are the same price. I'm looking at all aspects from sound quality, to build quality and functions features and what's going to be easier to live with using everyday.

Thanks in advance :blush:

Edit: Figure that a bit of a run-down of the rest of the system will be helpful

Most of the components I already have from my previous car so they will be used..at least for now:

GM5100T 2x125WRMS Bridgable

GM6300F 4x60WRMS (will be used to power the speakers)

Lightning Audio Strike 15" Single Coil in 1.5Cu.Ft.

4Gauge Schneider OFC

Gold 4Guage in 2x 8Gauge out Fused Distribution Block

2x Sony RCA Signal Leads

1x Jaycar RCA Signal Leads

I would like to replace the 15" sub with 2x12" woofers as I listen to all types of music and for some certain Genres I prefer to have an in between of tight bass and low deep bass..but that may come later, I'll just use what I have for now.

Edited by N-DAWG
  • 1 month later...

hey!

as far as the headunits go, ive got an alpine CDA 9885i and its sweeeet, plays so well, its never skipped and ive had sum reall scratched cd's in it. features r u can change the colour of ur main opperation buttons between red and blue, u can controll ipod from headunit not from ipod, i think its the same with bluetooth, havnt set that up yet, can have background visuals while lsitenin 2 music, comes up wit notes sayin happy new year, xmas, u can even set ya b-day in it fo it 2 say happy b-day lol as for speakers ive got S type 6.5inch speakers front and back aswell as a 12inch S type sub all amped from a 1200 watt amp and thats loud enought rearview mirror vibrates like hell and cant c out of it when on max vol lol :banana: no distortion on front and rear speakers from 2 much bass, crisp & clear music, my girlfriend says she can hear it from her room at the back of the house and can hear word for word, das how clear it is. if S types sound really gewd id think R types or even X types would b crazy! :D

Alpine 9887 ftw!

R-types are good(I've got splits up front, coax up back), but I think you'll need a spacer for the 6.5' speakers, the r-types actually come with some, but I can't remember if they were enough to clear the frame or not, mainly because I already had mdf spacers in there.

hmm i wouldnt bother bridging the 4ch down to 2 channels to run the fronts. At the end of the day you will be running it through a high pass filter in your SQ install to keep thclraity up, which means that they do not need a huge amount of power. You would do better to run a speaker off each channel ie amp your rears as well, thus giving you an even sound from front and read, as opposedto just a massively overpowered front stage.

pretty sure that ur pioneer 2xh is going to underpower that sub, too. For SQ, you want to have an amp that puts out a highr RS than your sub, then only run it at 1/2 to 2/3 gain so that it isnt maxing out. You get better sound when your components arent at their limits. Plus, a 15 in the boot of a car isnt the best for SQ. They take a bit of power to deliver the punch you need.

Type R Fit just but with spacers... and sound like shit, trust me I tried it.... DD liner sound much better. but if you can stay away from /////ALPINE the better.

Edited by Hotr34

Hey guys

Thanks for the replies.

I ended up getting the bits mid/late Feb and just remembered I'd posted this thread :D

Some great replies there too.

I had to lower my budget a bit due to unexpected expenses that managed to pop up but I think i still managed to do well considering how much I saved on the bits I bought.

I ended up buying the Kenwood X8006U Head Unit, saved about $300. It covers the iPod control without purchasing any additional cables etc, has 3pairs of 5volt, covers the tuning aspects that I wanted and leaves me with room for expansion later on.

I installed NV Splits up front and powerplant 2-ways in the rear shelf..the price was right for these parts and they don't sound too bad considering. And yes I had sound deadening fitted for the front speakers, though I'm considering doing the door skins as well later on.

For reference, the NV Splits just fit. The installer had to cut into the plastic on the factory speaker mount to fit the depth, but I was told it just cleared.

I was nearly going to get a pair of Orion splits (ex display models) which would have set me back around $400 a pair, though the saving was quite huge. I can't remember the model of these but they were almost like a miniature sub in design.

As for the 15" sub...I would really like to sell it and buy a pair of 12" woofers (undecided which ones at this stage) and I may even do a custom enclosure to make the most of the R34 boot space. For now I'll just keep the sub though until such time as I'm ready to upgrade it...besides I'm saving towards getting exhaust work done at the moment so the sound system will be fine for now :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi everyone, I'm about to complete my first single turbo conversion on my R32 GTR and I thought I would post the step by steps that I will be following. I will list the parts I have / the parts I will be buying. I will be redoing this guide after I have completed the conversion. Parts list: - 3576 turbo 0.82 v-band (coolant and oil)  - v-band top mount turbo manifold - 50mm wastegate - manifold copper gasket - titanium manifold stud kit - turbosmart 3 port boost solenoid - link can lambda kit (wideband) - link ECU - radium 12AN push in valve cover fittings (pair) - hi octane catch can - 3.5inch downpipe - screamer pipe - pipe from turbo to intercooler - intake pipe setup - power steering relocation kit - oil drain block off plate - coolant and oil lines Now onto the step by step guide (please add / correct me if there's anything I missed: 1. remove fluids, twin turbo pipes, pod filters and afm's 2. remove the factory coolant hardlines from the hot side. 3. remove heat shields  4. remove the downpipe 5. remove turbos and manifolds 6. remove factory manifold studs 7. clean whatever mess you have made 8. install power steering relocation kit 9. install new manifold studs 10. install new turbo manifold with gasket 11. install new wastegate with screamer pipe 12. install new turbo  13. install new coolant and oil lines  14. install rear oil drain block off plate 15. stop and appreciate that you now have a single turbo in your GTR 16. wipe away tears of joy and install downpipe 17. install the wideband sensor into downpipe 18.install pipe to connect turbo to intercooler 19 .remove stock boost solenoid  20. install new boost solenoid 21.  install intake setup 22. setup the rest of the can lambda kit with the ecu  23. refill fluids and hope for the best 24. ask forums for help with issues 25. fix issues 26. drive your single turbo swapped r32 GTR into the sunset. Doneeeeeeeeeee. Now I know this isn't detailed at all but I will be doing that when the conversion is done. I will be posting pics and any helpful details i can and ill make sure to fit in as much information as I can. If there's anything I should know before i do this PLEASE let me know. Stay tuned for what's next. Thanks...
    • I have wasted too much time on this, more than I am willing to admit. I hope someone can set the record straight for me.  I want to replace my Nismo (non GT pro, non GT) standard 2 way in my R33 GTST with a 1.5 way... Ideally I want to get an ATS 1.5 way Carbon LSD, but I don't want to reuse my 29 spline 5x1 axle stubs, and new 30 spline 5x1's are impossible to get a hold of ($$$), and I don't want to drop the cash on going to 6x1 stubs and axles ATM. Which leads me to the Nismo GT Pro 38420-RSS15-B5 or RSS20, as they come with new axle stubs meant for the diff, and is "Convertible" from a 2 way or 1.5 way to "Other ways", but that is where I am stuck as the documentation is a bit all over the place.  To sum up what I have found I believe the all the Nismo GT Pro PN's are convertible from 2 way, 1.5 way, and 1 way; but Nismo sells 2 skus (2 & 1.5) so people do not have to disassemble to convert it.  I found this thread on 350z but it left the question unanswered. https://my350z.com/forum/engine-and-drivetrain/620032-nismo-gt-pro-lsd-1-5-vs-2-way-and-torque.html  Essentially the way I think it all works out is like follows...  2 way  1 way  and 1.5 way would be the center pinion shaft in the 1 way block, but with the with the center flipped 180*. So the ramped side of the pinion would face the 1 way gate and act like a ramp.    I can only get my hands on the 2 way in the states, and I am not trying to get stuffed on tariffs by ordering from Japan or anywhere else. I want to confirm that if I get the 2 way I can convert it to the 1.5.     
    • Hi everyone, I have purchased my first GTR and I want to do a single turbo conversion to it. I've been doing as much research as i can and there are a few things that I can find and need to know. I need to run a coolant feed, coolant return, oil feed and oil return for my turbo setup. Here's what I know so far: On the hot side of the rb26 there is coolant feed, oil feed and oil return. Coolant return will be going around the front of the engine to where the thermostat is located. I will need to block off the rear oil return port. I will be running a turbosmart boost solenoid so any of the factory boost stuff wont be needed. Now onto what I don't know: 1. What do I do with the coolant / vacuum hardlines that run around the back of the motor?. 2. What do I block off or loop or move or remove?. I will be running the OEM intake manifold. 3. Is there anything in particular I need to buy for the cold side of the rb26?. I already have the intercooler and pipes sorted. If you have any pictures or information it would be appreciated. Thanks....  
    • The fab work can be as simple as a couple of silicon hoses and clamps to the factory piping. 
    • Just sounds like either way you need to do some fab work to get everything to fit, so why limit yourself at that point? If the GCG high flow option is zero effort in and out swap though I'd probably do that. It's almost certainly lowest risk, lowest cost, etc. The HKS GTIII-RS option that Kapr mentioned is laughably expensive for what it is, they charge the exact same for two turbos on the RB26 so their margins are off the charts on that thing.
×
×
  • Create New...