Jump to content
SAU Community

Recommended Posts

HI all

I have this annoying clicking noise coming from behind my aircon unit when i start the car.

it happens for about 30 seconds then stops.

It is getting pretty annoying does anyone have the same problem? and if so how did you fix it?

its an r33 gts-t.

any help will be great.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/206019-annoying-clicking-noise/
Share on other sites

The clicking noise is from your Air Blend Servo motor (controls hot/cold mix). The gearteeth that control the flap have slipped off. It is really easy to fix, the only problem is removing the whole dash to get to it.

Easiest way is to make sure the heat is maxed all the way up, i.e. slam the red button a million times before u start the car (can be on or off), wont make the sound - leave it like that and wont happen again

hey jmaac

thanks for the advice.

would you know where abouts this blend motor is located on the unit

as due to my ever changin audio needs im somewhat of a pro at dash

removal now :whistling:.

and what to look for in the unit. will the gear be off or could it be that the

teeth have been shaved off.

Thanks

the teeth have basically worn down due to use, they skip over each other as they try to engage causing the click click noise.

i've currently pulled my dash apart to fix it. it's not a small task, at least a 3 hour job to take the dash out.

see attached, note the red arrow on the gear.

the blend door motor is located right in the middle of the dash, above the heater box.

post-9983-1203031896_thumb.jpg

post-9983-1203031962_thumb.jpg

same thing has happened to mine, after a few months im getting a very nast smell eveytime i turn up the heat. i then noticed a wet patch under the dash of the passanger side. If i fix the noise would i stop the damn thing from leaking?

Smell is normal, remove the glovebox and theres a panel which u can remove to clean aircon filter elements

This wet patch is bad, either means your heater coil has rusted out or a hose is broken (b/n firewall and heater)/hose clamp needs tightening (Unless condesations is somehow running back down into your car). U can tie off your heater in the engine bay and loop it around or fix it properly.

Im not sure if u can get replacement gear for these or one from a hobby shop to fit. I used a little glue and was able to build the gear back up, but it didnt last very long. If anyone manages to get a replacement (not 2nd hand) can u please let us know, I may make an plastic injection mould if not avail.

same thing has happened to mine, after a few months im getting a very nast smell eveytime i turn up the heat. i then noticed a wet patch under the dash of the passanger side. If i fix the noise would i stop the damn thing from leaking?

Noise has nothing to do with the leaking. The leaking is probably your heatercore, better to replace it sooner rather than later. The leak will only get worse, and where do you think that water is coming from? Your cooling system - better check and top it up :teehee:

You can bypass the heatercore if you like, just look for the 2 heater hoses going into the firewall on the passenger side, and connect them....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
×
×
  • Create New...