Jump to content
SAU Community

Trackday Sandown 15th March Our Cheapest Ever Trackday


Recommended Posts

especially when it's going to be 35 degrees :thumbsup:

think that Royal Purple 5w30 will be up for a 35 degree track day?

do we have to have our own helmet, or can we borrow one on the day?

Glad I'm using 5w40 :D, just watch your oil temperature and if its getting too hot its time for a break ;)

You normally bring your own helmet, you can ask Kevin if you want to hire, I don't know how many helmets he has.

Regards,

Gareth

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

true, but i'd rather use a full synth 3w50 than a semi synth 5w40

Well yes, you should be using good quality fully synthetic oils

I might see you at the track day? :thumbsup:

last time i did this we had a few hot laps and a cool down lap. then more hot laps. until somebody decided to dump their sump all over the track! just check all your gauges esp temps and have a great time. Make sure you have a sump plug not a spark plug and make sure its tight! :laughing-smiley-014: if im free ill come round with the camera for some happy snaps.

last time i did this we had a few hot laps and a cool down lap. then more hot laps. until somebody decided to dump their sump all over the track! just check all your gauges esp temps and have a great time. Make sure you have a sump plug not a spark plug and make sure its tight! :laughing-smiley-014: if im free ill come round with the camera for some happy snaps.

and make sure ur sump plug is tight :thumbsup:

btw if anyone wants to take my spot pm me

Well yes, you should be using good quality fully synthetic oils

I might see you at the track day? :P

sorry, that came out wrong. i was thinking in my head, and forgot to type, that i've changed an order from 5w40 castrol syntec (not full sythn) to Royal Purple 5w30 (full synth)

be informed it should be ok, but never hurts to have some opinions.

Yeah dude, def see you at the track day! I think it's fair to say we've both been running around like idiots getting our cars ready :) I'm still got some fluid changes and brake pads to go, and i should be semi happy bout my prep.

How's your car coming along?

i "think" we also did a driver training day together as well.

Woohoo, dregraded from 35 deg C to only 30 :D

still :s

Cars in to get the steering fixed today, get a tower brace and should be getting the bonnet pins on tonight, i'll be buying a fire extinguisher tonight too... just in case to worst happens :s

Was fitting an exhaust to a mate's S13 who's going, till midnight last night. So much to do, so little time.

from the Kevmeister

"Hi Daniel

We only have one or two helmets available on Saturday, it would be best if you brought your own helmet."

in case people were banking on borrowing one, probably best to bring your own

cheers :)

Yeah dude, def see you at the track day! I think it's fair to say we've both been running around like idiots getting our cars ready :( I'm still got some fluid changes and brake pads to go, and i should be semi happy bout my prep.

How's your car coming along?

i "think" we also did a driver training day together as well.

Hey, we may have done the driver training day together, I'm terrible with names :)

No brake pads so if I can't do too many hot laps then I won't.

Brake fluid I haven't done, I'll get my car back tomorrow evening so I'm going to get it and do the brake fluid change tomorrow night (so disorganised).

Do you know how much fluid I'll need? Need to find some quality fluid, Motul RBF600 :)

Regards,

Gareth

buy more brake fluid then what you will need. can never hurt to have a bottle spare. when i was last at sandown, i reamed my whole brake system. rotors badly, fluid was cooked, pads... i got new rotors brake pads braided lines and fluid all cos of a day at sandown

Was fitting an exhaust to a mate's S13 who's going, till midnight last night. So much to do, so little time.

lol tell me about it, I worked 4 12hour 3-3 shifts this week, then in the afternoons have put in an oil cooler (which ended up having to be totally

custom fitted), ally radiator and new rotors....bedtime now I thinks, see you all tomorrow

Had a great day... just have to load the photo's up...

Anyone get pics of my Gazelle? The Silver one with the orange engine bay :nyaanyaa:

The silver R33 GTR was NUTS!!! There seemed to be more than a few Skylines there all doing rather well... It was interesting to see the different stages how the different cars went.

Great day besides the heat...

Now to sort out the issues that arrose from pushing it in those temps :s

Edited by gadget1382

A bit late, but just wanted to say thanks to Kev and the crew for putting on a great day. Plenty, plenty of track time, great instructors, lots of drinks :D

Highly recommend anyone wanting to get into this sort of thing to go to one of these days. It was my first real "track" day, and was a great way to start out.

Nice to meet some of the sau peeps as well :) Gareth, Kyle.

Kyle, i thought you had a GTR, what's the go dude! :D

(just the beginning bit)

32.jpg

thanks again guys :)




  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...