Jump to content
SAU Community

Recommended Posts

Item: Cusco Rear Upper Arms

Condition: BRAND NEW

To Fit: R32 GTR

Location: Lower North Shore, Sydney

Contact: Andrew ([email protected] or 0418 881 113)

Price: $400

Comments:

231 474L Nissan - Skyline BNR32 - +10 to -6mm

FEATURES

- Provides proper camber angle and improves car movement

- Prevents irregular tire wear and holds tire to the asphalt, improving traction.

- The good alignment will enable better traction as well.

- The turn buckle will correct the camber with the change in height.

Actual Photos:

cusco_rear_upper_arms_1.jpg

cusco_rear_upper_arms_2.jpg

cusco_rear_upper_arms_3.jpg

Item: Cusco Front Pillowball Tension Rods

Condition: BRAND NEW

To Fit: R32 GTR or GTS-4

Location: Lower North Shore, Sydney

Contact: Andrew ([email protected] or 0418 881 113)

Price: $340

Comments:

231 473 ASN Nissan BNR32 RB26DET

FEATURES

Reduces the amount of suspension flex during hard cornering.Increases greatly the handling response going into corners by adopting pillow ball mount on the body side. High rigidity pillow rods balls used to hold down tires under braking. Increases straight line stability by reducing toe out and friction.

The turn buckle type allows simple adjustments with the parts on the car.

The pillow balls are covered by rubber boots for increased durability.

Actual Photos:

cusco_tension_rods_1.jpg

cusco_tension_rods_2.jpg

cusco_tension_rods_3.jpg

cusco_tension_rods_4.jpg

Item: Trust Sump Extension

Condition: BRAND NEW

To Fit: Any GTR or car with RB26 engine

Location: Lower North Shore, Sydney

Contact: Andrew ([email protected] or 0418 881 113)

Price:$440 SOLD!

Comments:

13525900 Nissan RB26DETT Oil Pan Up Grade Kit

Cure for your Sump Baffle Syndrome (SBS) :cheers:

When the vehicle is on the corner or the time of acceleration and deceleration, oil in the oil pan will lean or jump. To prevent these to happen, a baffle is assembled in the pan of stock engine. Though, in terms of sports driving, it is almost impossible to achieve its purpose because the size of the baffle is restricted to cut down the production cost. If oil flows to one sidey, air goes into the pipe instead of oil and interrupts the continuous oil lubrication. Without oil, metal surfaces will contact directly with each other, then the temperature rises, causing wear. On the other hand, Trusti movable baffle plate is made to achieve stable oil lubrication at any situations such as curving, acceleration, and deceleration. And it will secure the improvement of engine performance from street use to the drag racing or circuit run.

Actual Photos:

http://www.andrewho.com/misc/forsale/trust_sump_extension_1.jpg

http://www.andrewho.com/misc/forsale/trust_sump_extension_2.jpg

http://www.andrewho.com/misc/forsale/trust_sump_extension_3.jpg

  • 1 month later...
  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...