Jump to content
SAU Community

99 R34 Gtr V-spec W/ N1 Runnimg Gear And Many Extras

EMPIRE AERO
 Share

Recommended Posts

EMPIRE AERO Rising Star

EMPIRE AERO

Posted
Posted (edited)

Black nissan r34 gtr v-spec 1999 model

18x10 bbs lm wheels with brand new nankang tyres,

full n1 running gear -eg. block, turbos, pistons etc etc etc

power fc d jetro w/ hand controller

FULL NISMO KIT

TOMEI OIL Gallery restrictor

TOMEI　metal gasket set

TOMEI　OIL pan baffle kit

NISMO reinforced timing belt

REIMAX camshafts　IN2648.58 EX256 8.28

HKS actuators

NISMO strengthen engine mount

NISMO FUEL PUMP

NISMO 550CC INJECTORS

HKS PIPING KIT

NISMO SWAYBARS

APEXI 3 LAYER RADIATOR

HKS OIL COOLER KIT

APEXI SUCTION KIT

AND LOTS MORE THATS JUST OFF THE TOP OF MY HEAD!!

PM ME FOR PICS AND ILL EMAIL THEM :D

THX

Edited by SRB_empire
  • 3 weeks later...
supadan Rising Star

supadan

Posted
Posted

ok lol sounds good so ill start saving hard so i can get this if its still for sale wen iam ready. cause this has all the stuff that i wont to do already done.

EMPIRE AERO Rising Star

EMPIRE AERO

Posted
  • Author
Posted

to get all this done would cost upwards of 30k in PARTS alone. VERY cheap for what it is, like ive said to many ppl in emails, i cant afford to keep it, priorites have changed and i need to expand my business, and am considering trades upto and around the 25k mark

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...