Jump to content
SAU Community

Recommended Posts

Hey guys, I've currently got these for sale! I bought these a while ago hoping to put on my car. However I'm happy with the power its making with a FCD and profec b spec 2 only! I'm guessing if I put these in and had a tune, it would be in excess of $1000 with only 10-20rwhp gain.

SAFC 2 Special edition: used condition with harness labelled. Comes as is, no manual, but they can be easily downloaded form greddy site, or I could just email it to you.

Price: $270 ono(SOLD PENDING PAYMENT- STENVE)

safc2d1specialedza8.th.jpg

Greddy Profec E-01: used condition, with all the necessary things! Downside is that the harnesses have been cut, but the harnesses only contain 2-3 coloured wires which can easily be soldered and heat shrinked together again.

Price: $400 ono

greddyprofece01dy0.th.jpg

Greddy pressure sensor with harness: used condition as well, with harness also cut but easily soldered and heatshrinked back. suitable for Emanage's. I'm guessing its the the 3bar one available on nengun for $116+49(not incl shipping)

Price: $100 ono

greddypressuresensorharoo2.th.jpg

The above prices are just an approximation. i don't know the market prices as such, but I'm willing to negotiate to an extent! so shoot me a reasonable offer and we'll take it from there!

Also with the harnesses. I can solder them and heat shrink them back for you if need be. Just hadn't had the need/time since i bought them.

Anyways you can post here/pm me/call me on

0433 458 783

Willing to post at buyers expense!

Edited by teknoboi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...