Jump to content
SAU Community

Recommended Posts

Hey guys

i've just got word that people are organizing another riot in noble park on block buster.. i know theres no reason to bring it up here but there is reason.

one: ..i would like to know if any one else has heard and where they did , as its been said that people on another forum (unkown) are organizing it and,

two: .. my girlfriend is the manager for maccas and shes very concerned about her store and staff tonight...

and frnkly if shes stressed and worried all night how can we have fun on her night off :P

cheers for the help guys

Link to comment
https://www.sau.com.au/forums/topic/208449-another-riot/
Share on other sites

I was driving near there (Browns Road) no more than 45 minutes ago, had no idea of anything strange going on. Seemed pretty quiet. Know if anything ended up happening?

Edit: Very nice picture. :P

Edited by rh1n0
Link to comment
https://www.sau.com.au/forums/topic/208449-another-riot/#findComment-3687470
Share on other sites

This wouldn't be happening if they had have invested in my proposal...

NPskidpan.jpg

I notice in this picture you make references to Serb Crowds and Cro's....Well is that how it happened at Noble park ?....Last I heard it was a bunch of out of control Aussies....So why try to pin something on the slavic people.....? Accept your own wrongdoings and dont point fingers....

Link to comment
https://www.sau.com.au/forums/topic/208449-another-riot/#findComment-3687476
Share on other sites

I notice in this picture you make references to Serb Crowds and Cro's....Well is that how it happened at Noble park ?....Last I heard it was a bunch of out of control Aussies....So why try to pin something on the slavic people.....? Accept your own wrongdoings and dont point fingers....

first of all you're assuming i'm not croatian or sebian, secondly you're assuming i'm full aussie.

Learn to take a joke people, like everyone else did when I made it over a year ago...My cro friends have seen it and laughed, my serbian friends have seen it and laughed :P

and for those that need it explained to them, you'll notice that there's a small portion labelled as serbs, and a small portion labelled as cro's....are you assuming that the rest of the ms paint dots are all serbs and cro's? or could there be all kinds of races in there ? :)

Also, I don't see a reference to either the serbs or cro's rioting....perhaps you could point it out to me

Link to comment
https://www.sau.com.au/forums/topic/208449-another-riot/#findComment-3687492
Share on other sites

and for those that need it explained to them, you'll notice that there's a small portion labelled as serbs, and a small portion labelled as cro's....are you assuming that the rest of the ms paint dots are all serbs and cro's? or could there be all kinds of races in there ? smile.gif

Also, I don't see a reference to either the serbs or cro's rioting....perhaps you could point it out to me

There are arrows point to the dots and are labelled cro and serbs, you might not mean harm but when people read cro/serb at the same place they automatically think riot/fight etc

its the same stereotype Aussie V lebo in the Cronulla riots, as soon as a lebo is spotted they think his after trouble

Edited by SLYNE
Link to comment
https://www.sau.com.au/forums/topic/208449-another-riot/#findComment-3687512
Share on other sites

and people need to let it go. this is Australia.

Even the Serbian/Croatian sports stars think what goes on here is ridiculous. They live in the respective countries and they're fine with it...then they come here to play and see riots.

Yeah I hear what your saying, however there are plenty of nationalities here that hold grudges toward each other...Aussie/Leb, Or maybe Indian/Pakistani...Greek/Macedonian..Greek/Turk..the list goes on.Too many young idiots brainwashed by older idiots cause this hooligan behaviour

Link to comment
https://www.sau.com.au/forums/topic/208449-another-riot/#findComment-3687521
Share on other sites

Yeah I hear what your saying, however there are plenty of nationalities here that hold grudges toward each other...Aussie/Leb, Or maybe Indian/Pakistani...Greek/Macedonian..Greek/Turk..the list goes on.Too many young idiots brainwashed by older idiots cause this hooligan behaviour

my point exactly. so have a laugh at a harmless picture and let it go.

And I know plenty of Aussies that hate Aussies, wogs that hate wogs, lebos that hate lebos, and any other nationality you can think of, I work with plenty of ALL of them everyday.

Don't break shit down into race, and its just people hating people :P

Link to comment
https://www.sau.com.au/forums/topic/208449-another-riot/#findComment-3687531
Share on other sites

People will probably take offence to that ms pain masterpiece because for some people its true. Maybe when people move to Aus they should pull their heads in and leave their grudges at whatever place they came from. :down:

Link to comment
https://www.sau.com.au/forums/topic/208449-another-riot/#findComment-3687560
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...