Jump to content
SAU Community

Recommended Posts

I have recently been on a few long trips, ie up the coast, and dubbo(the zoo is good!)

On these trips due to a lack of traffic, and me taking the long, back way a lot of the time, the speeds often stayed up around 150km/h, equating to about 4300rpm (cant remember exactly) for extended periods (more than half an hour at a time).

I was wondering if anyone could tell me how bad this is for the engine, especially in terms of piston ring and bore wear.

I felt bad leaving the revs so high for so long, but then again, because most of the time i was not accelerating or decelerating, is it true that the sliding friction between the piston rings and the bores is small because of the lack of accel/decelerating, and therefore not so bad?

This question has also been in the back of my mind in relation to my swift gti, where on long trips, revs stay even higher than in the skyline due to the shorter gear ratios.

I'm not sure if the same applies in Aus, but in England a car that has many motorway miles is considered a better buy than a car with equivalent miles done around town - the thinking being town driving with constant start/accel/brake/stop wears out components quicker than a steady cruise at a fixed speed...

Yeah thats what i was thinking, but then again, i think the general reason why more wear occurs in the city is because when the engine is idling, it runs quite rich, which in turn increases the amount of petrol which makes its way into the oil, in turn breaking that down faster, creating less protection for the engine and more wear.

Oh well, at least other people think its ok, im still half way about it. 2night i drove my swift at 5 grand for about 3 minutes, that felt bad. Maybe im just paranoid.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...