Jump to content
SAU Community

2008 Drift Practice Days @ Baskerville


grandmasterb
 Share

Recommended Posts

Here are the dates for the drift practice days at Baskerville Raceway for the remainder of the year. Hope to see everyone out there having fun and having a go in a safe, legal environment. These practice days for enthusiasts of all skill levels and budgets, everyone is welcome!

- April 19

- June 28

- September 13

- November 8

The above practice days will run exactly like the other drift practice days in Tasmania. IE: NOT run as a CAMS event, thus not requiring the usual requirements such as a CAMS level 2 licence, pass CAMS scrutineers etc etc.

ALL PRACTICE DAY TIMES: 10AM - 4PM

To make it clear these days are NOT a competition, there will be no top 16, no judging just everyone going out and improving their drifting techniques on the track. Passengers WILL NOT BE allowed.

Practice will be in the form of single car runs ONLY (ie. no tandems). Tandems are not allowed due to track insurance reasons. Basically there would be no insurance should two cars be drifting in tandem, because of this it is single runs only.

There will be a drivers briefing at 9:45AM FOR ALL PRACTICE DAYS. ALL DRIVERS wanting to drive MUST attend this briefing before heading out on track. PLEASE DO NOT BE LATE!

Throughout the duration of the event there will be NO CARS allowed across the track UNLESS there is an emergency OR a valid exemption (which must be approved by a committee member before the gates will be opened).

There will be 30 minutes at the end of the day designated for all drivers to assist in sweeping the track surface and edges to return it to an acceptable condition. ALL DRIVERS MUST PARTICIPATE IN THE SWEEPING OF THE TRACK!

REQUIREMENTS:

The entry fee for this practice day is the same as it would be if you were going out to do some practice laps, which is $55 IF you are a member of a Motorsport Tasmania & CAMS affiliated car club such as the Hobart Sport Car Club or the Light Car Club of Tasmania. IF you are not a member of such club the fee will be $115.

The fees are to be paid on the day.

SAFETY REQUIREMENTS:

ADR approved helmet

long sleeve shirt (flame retardant)

long pants (flame retardant)

appropriate foot ware (doesn't have to be race boots or cover the ankle)

and a general road/track worthy car

The following safety items are recommended, but not 100% required:

fire extinguisher and metal bracket

battery and tow indicator (stickers)

secondary bonnet restraint

ANY competitor will/can be asked to leave the track if found not following instructions of the day or doing the wrong thing that would danger themselves and others.

This can and will result in the person being banned from the track and future days.

For further details or clarification of anything written in this thread feel free to PM me.

Cheers.

Ben

PLEASE NOTE- IF YOU DO NOT ASSIST IN THE SWEEPING OF THE TRACK AT THE END OF THE DAY AND ARE NOT GIVEN AN EXEMPTION TO DO SO THEN YOU WILL NOT BE ALLOWED TO PARTICIPATE IN THE NEXT PRACTICE DAY.

Any questions or comments:

PM Ben Purtell aka tas_180

[email protected]

0408 782 632

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
 Share



  • Similar Content

  • Latest Posts

    • Hi all, I need to get this HKS SLD attached to my stock ECU because I've now got the German autobahn and faster European circuits to contend with.  The car is a manual 2dr ER34 with an AT ECU and I've realised the AT ECU has two pins for speed sensor signals: Pin 29: Vehicle speed sensor signal (Vehicle speed sensor 2) Pin *58: Output shaft rotation sensor signal (Vehicle speed sensor 1) - *RB25DET A/T model only Before I go butchering this harness, is anyone sure of which pin is the correct one for signal adjustment? The attached document from HKS indicates pin 29 but I found this situation mentioned in the following thread on a different forum (R34 GTT Auto Trans Speed Cut Problem | Zerotohundred) mentioning pin 58 needing to be altered by member zephuros, albeit it seems to be for an RSM-GP and the info appears to be old.  R34_All_Workshop_Manual-pages-2.pdf R34_All_Workshop_Manual-pages-3.pdf R34_All_Workshop_Manual-pages-1.pdf HKS SLD Vehicle Pin out P59-P70 ER34-pages.pdf
    • Embrace the freedom of casual encounters on the best dating app in town! Verified Maidens Superlative Сasual Dating
    • Slimline sub on the rear parcel shelf is doable. Pioneer TS-WX140DA is only 70mm high.   
    • People like Johnny Dose Bro might be laughing at my post because I accidentally added 100mm to my numbers. 350-355 is indeed the lower limit. 450 is off-road Skyline spec.
    • What is the "compromise" that you think will happen? Are you thinking that something will get damaged? The only things you have to be concerned about with spherical jointed suspension arms are; Arguments with the constabulary wrt their legality (they are likely to be illegal for road use without an engineering certificatation, and that may not be possible to obtain). A lot more NVH transmitted through to the passengers (which is hardly a concern for those with a preference for good handling, anyway). Greatly increased inspection and maintenance requirements (see above points, both).   It is extremely necessary to ask what car you are talking about. Your discussion on strut tops, for example, would be completely wrong for an R chassis, but be correct for an S chassis. R32s have specific problems that R33/4 do not have. Etc. I have hardened rubber bushes on upper rear control arms and traction rods. Adjustable length so as to be able to set both camber and bump steer. You cannot contemplate doing just the control arms and not the traction arms. And whatever bushing you have in one you should have in the other so that they have similar characteristics. Otherwise you can get increased oddness of behaviour as one bushing flexes and the other doesn't, changing the alignment between them. I have stock lower rear arms with urethane bushes. I may make changes here, these are are driven by the R32's geometry problems, so I won't discuss them here unless it proves necessary. I have spherical joints in the front caster rods. I have experienced absolutely no negatives and only positives from doing so. They are massively better than any other option. I have sphericals in the FUCAs, but this is driven largely by the (again) R32 specific problems with the motion of those arms. I just have to deal with the increased maintenance required. Given how much better the front end behaves with the sphericals in there.....I'd probably be tempted to go away from my preference (which is not to have sphericals on a road car, for 2 of the 3 reasons in the bulleted list above), just to gain those improvements. And so my preference for not using sphericals (in general) on a road car should be obvious. I use them judiciously, though, as required to solve particular problems.
×
×
  • Create New...