Jump to content
SAU Community

Recommended Posts

Hi guys,

I recently bought an R34 GTT tiptronic coupe, my first Skyline but I have owned many turbo cars over the years.

Current mods are limited to a HKS catback exhaust (came with the car) and since reading your illustrious forum I have done the free dual stage boost disable mod and ordered an R32 wastegate actuator (havn't had time to fit yet) but have been told this will give me a solid 10psi.

Basically I commute a lot in traffic which is why I chose the auto, I'm usually a manual man. I find the tiptronic pretty good and not too boring but it does have that auto syndrome where it takes a while to get moving on light throttle applications. So I'm really chasing low down/mid range urge combined with decent fuel economy. I must say I was dissapointed with the first tank - 320km then the fuel light came on (my 03 WRX used to give over 400km every time with spirited driving).

From research I have done on here my options for further mild performance mods could include:

- front/dump pipe $199 approx.

- High flow cat - $180 approx.

- Apexi SAFC NEO - $295 + install and tuning

(above are the best online prices I have found)

Now I'm thinking for under $1000 the above would give me a nice little gain - BUT I dont want to ignore cosmetic mods either. Unfortunatly car did not come with a rear wing so I am desperatly trying to source one (PM me if you have one) and also thinking some nice lowered Tein springs and some 18" black rims would finish the look off nicley (car is white).

Of course all of this adds up so what in your esteemed opinions should I be looking at first? I am keen to get the fuel consumption under control which I have been told an SAFC should be good help - but is there any point in installing one without doing the dump/cat first? ect ect. Because if I do the dump/cat later surely it would then require a costly retune??

Any comments appreciated!

Edited by colossus
- Split/dump pipe $199 approx.

- High flow cat - $180 approx.

- Apexi SAFC NEO - $295 + install and tuning

(above are the best online prices I have found)

Got links to those prices? $199 for a split dump and $295 for a AFC NEO seem a little too cheap.

Anyhow, i'd definately be doing the split/dump and the high-flow cat... then having your afc fitted and tuned. See how you go, before spending money on a turbo upgrade, computer management, etc.

Do the mods, you will get gains. The full exhaust will give you meatier acceleration.

Fuel consumption= service the car if you haven't. I mean fresh synthetic oil+filter, NGK plugs, clean the AFM, throttle body cleaner, flush the intercooler with degreaser, clean oxygen sensor, injector cleaner and only use top fuel (IMO V-Power or Ultimate).

Since i did all this my Skyline pulls 500km per tank (manual).

Got links to those prices? $199 for a split dump and $295 for a AFC NEO seem a little too cheap.

Anyhow, i'd definately be doing the split/dump and the high-flow cat... then having your afc fitted and tuned. See how you go, before spending money on a turbo upgrade, computer management, etc.

Woops edited original didn't mean split but it is a dump/front pipe in one. Still good prices - they are from Just Jap.

Do the mods, you will get gains. The full exhaust will give you meatier acceleration.

Fuel consumption= service the car if you haven't. I mean fresh synthetic oil+filter, NGK plugs, clean the AFM, throttle body cleaner, flush the intercooler with degreaser, clean oxygen sensor, injector cleaner and only use top fuel (IMO V-Power or Ultimate).

Since i did all this my Skyline pulls 500km per tank (manual).

Thanks I'll give this a go - its got about 99,000kms so getting due for the 100,000km service anyway - which is going to cost a bomb just in parts ($100 for sparkplugs is ridiculous) - I'll do it all myself of course. Can you clean an O2 sensor? not having much luck finding a new one under $200 to fit an R34 (not sure if the EL one fits R34).

Thanks I'll give this a go - its got about 99,000kms so getting due for the 100,000km service anyway - which is going to cost a bomb just in parts ($100 for sparkplugs is ridiculous) - I'll do it all myself of course. Can you clean an O2 sensor? not having much luck finding a new one under $200 to fit an R34 (not sure if the EL one fits R34).

Just get copper plugs. $25 a set and change them every 10-15,000kms or so. If Iridiums get fouled they're not much use.

Yeah most of the servicing is easy. The O2 sensor can be carbie cleaned to wash off the carbon buildup. That should do the trick.

Hope the mods get the power you want mate. Good luck.

yep, iridi/palti, whatever... $100 for plugs are a waste.

They VERY rarely last that long in a modified car.

Factory, yes no problem... but soon as you up the boost, exhaust, tune - coppers are the way to go and regular servicing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...