Jump to content
SAU Community

New blow off valve

howhow82
 Share

Recommended Posts

YBSLO4 Proficient

YBSLO4

Posted
Posted

The screw aloows you to adjust hte spring tension. When you are running more bosot pressure you might find it starts to leak in higher rev's so you want to tighten the srping up, however if you are not running as much boost you want to loosen it off to ensure the BOV will be able to open. However they more adjustable nowdays for rice factor to get different sounds.

YBSLO4 Proficient

YBSLO4

Posted
Posted

BOV"s are illegal for the reason being that they vent blow-by into the atmosphere... yes they can be noisey, yes they cause the car to run richer but its stated that they blow un-filtered air/oil into the atmosphere... stupid really, cos last time i checked the exhaust vented to atmo aswell?? But thats all good its only carbon monoxides and what have you, alot worse than the 'ocassional' mist of oil comin from a BOV.

P.s. Don't forget BOV's if they aren't a good design will cause crappy throttle response, and having a atmo BOV means you must re-spool that released amount of air. They have their pluses and minuses.

Steve Grand Master

Steve

Posted
Posted

As YBSLO4 mentioned BOVs are illegal if they vent to atmo, because cranck case gasses must exit the car via the exhaust, Road Traffic Act 1962 (from memory) in SA. These traffic laws are now pretty much consistant australia wide. So they MUST plumb back to be legal - like the stock one.

As for adjusting BOV, tighter will mean it takes more (boost) pressure for the valve to lift. Yes it will make less noise, but the fluttering noise you hear is air reversing through the compressor, slowing the turbo down (increasing lag) and putting strain on the turbine - this isnt too good for obvious reasons.

I adjusted mine by winding it back until the fluttering sound was almost gone. Almost, because if you wind it back too far, you may have the car stall at idle as it doesnt seal properly. Something to have a play with until you are happy.

Steve Grand Master

Steve

Posted
Posted

The only noise testing I know of that a car needs to be roadworthy has to do with the exhaust, this is done with the car at revs, and the EXHAUST is not to exceed 89dBs. This is conducted with the car at specific revs, not changing gear - so I am not sure how any copper gets away with defecting cars for excessive intake noise (how could it exceed 89dB?) or noisey BOV which wouldnt be measured if a car was being tested for compliance with noise regulations - only for atmo BOV or pod that doesnt comply with ADRs.

I have heard of people claiming to be defected for this, and I would love to know exactly what regutation/act it is that they would be in breach of?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • perry_r33
      Skyline R33 Sedan Tail Lights S2 - (2 SETS Available) Silver & Grey

      By perry_r33 · Posted

      Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
    • MBS206
      98 R34GTT 4k engine stumble

      By MBS206 · Posted

      List all of your mods. It sounds like an aftermarket ECU hitting rev limiter. Like a valet mode, or a cold rpm limiter? 
    • tylink720
      "Cheap" bolt on turbo on RB25DET NEO

      By tylink720 · Posted

      @Kapr Haha yeah thats the one. I missed that you had a built up engine, I wouldn't want to run it on there either then. It was good in my situation just to replace the original turbo on a stock engine. @MBS206Yep definitely not a replacement for anything name brand
    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
×
×
  • Create New...