Jump to content
SAU Community

Recommended Posts

I've posted them elsewhere but anyway....

1995 R33 GTS-T (red coz red is faster)

75,500km

Motul Engine Oil

FMIC

HKS Pod (no box or cold air feed)

2 stage boost controller (7psi / 12psi)

Custom 3" Front/Dump/Cat

Nismo 3" Cat-back

Standard Turbo

Standard ECU

Shootout mode

7psi = 190rwkw

12psi = 203rwkw (leaning out)

Standard mode

7psi = 177rwkw

12psi = 188rwkw

At the end of the day though its just numbers (hopefully that i'll turn into a 13.Xsec pass down the 1/4 in the not too distant future).

I'm also confident that I can get it alittle higher, maybe another 5-8rwkw from afew more cheap mods over the next 2-3mths.

dyno-203rwkw.jpg

Originally posted by Roy13

a std R33 has only 138rwkw's

Thats debatable as it depends on the condition of the ending. But yeah ~140rwkw is probably about right.

what is a FMIC?

Front Mount Intercooler.

benm, you think all stock ecu's run close to 12:1 afr at 12psi and have the afr line anywhere near close to that??? i dont think so dude!!! :D you have a chipped stocky ecu. stock ecu's with stock boost run around 10.5:1 afr! yours is being leaned out somehow and i suspect thats the reason for your very impressive dyno results.

as for my car, i'm happy with the power its making, its not all about peak power, its the area under the graph that counts. that said, i know where i can find power, my intake pipe is crushing under load i need to replace it with a fabricated pipe, as the HPI 34 did...

Benm this is what a std computer does, the lowest line is std boost at the time i think 8psi. The next line 14psi and the top line 12psi. Look at you 12 psi compared to mine std computers trip out over the mass of air going throught the air flow meter.

All R33 with FMIC, aftermarket computers and 15psi of boost only just make 203rwkw, just curios as to what is going on, my main idea is that you boost gauge is telling porkies! You may actually be running 15psi. Your injectors arn't going lean as they are good for about 215rwkw's.

Originally posted by Roy13

All R33 with FMIC, aftermarket computers and 15psi of boost only just make 203rwkw

Says who? Theirs no rule or law that says all cars make the same amount of power with the same mods. Infact i'd give u $100 if u could find 2 cars with identical mods making identical power outputs.

my main idea is that you boost gauge is telling porkies!

Whats my boost guage got to do with anything? The boost "gauge" has nothing to do with a dyno run. The boost is measured on the computer (Alot more accurately too).

Your injectors arn't going lean as they are good for about 215rwkw's.

Technically and in theory yes, but my injectors are 8yrs old and so is my fuel pump so who knows what they are "actually" running at. One thing I have learnt with cars (and dyno runs) is that you can't expect to bolt on the same mod as the guy (or gal) next to you and expect the same power increase, coz it just doesn't happen.

Also like i said... at the end of the day its just numbers. I'm 20sec slower around a track than a stock R33 considering I have more power. It doesn't all come down to power, thats just 1 thing of many.

I'm now chasing that 20sec not the 20kw.

Robo's, that's pretty normal. The higher the pressure the more fuel the ECU usually dumps in unless dictated otherwise by tuning. When you see the opposite it means you have maxed out your fuel system (pump/injectors).

Benm i'm not trying to give you a hard time , and i'm not all R33 with these mods get 203rwkw just that 203 is the most i've ever seen with all these mods they seen to vary from 190 to 203rwkw's with those mods.

My sugesting you boost gauge is saying i have never seen a R33 produce 203rwkw on 12psi, so my sugestion being maybe the dyno's preasure sensor is incorectly calibrated and you were actually producing 15psi. As you do have a 95 which seem to be the go with std computers!!

You have a point with your injectors but with problems as you sugest a graph of air fuel would not be so perfect i am to think. I am telling you this as nobody could give me any feed back on my dyno sheet.

If you wish to gain time not kw's i suggest using a plenom that faces the front mount and reducing the length of all the pipes and maybe diametre if you are going to only use the std turbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...