Jump to content
SAU Community

Recommended Posts

Alright, i'm need of some cash for some mods etc, and have too many wheels at the moment, so have these up for sale. As far as tyres go i can organise pretty much any size tyre for these with decent tread for a bit extra, let me know what ur after and we can negotiate on price.

----------------------------------------------------------------------------------------------------------

Item:

Volk/Rays GT-P Wheels

Incomplete set, see comments

17x9 +16 all round

5x114.3

Comments:

Polished dish, Powdercoated black centres. 3 complete wheels, 1 wheel is missing the centre disk. All in near perfect condition.

More Info:

http://www.nissansilvia.com/forums/index.p...owtopic=283226=

Price:

$700

Pics:

dscn8983gc6.jpg

dscn0037wl3.jpg

----------------------------------------------------------------------------------------------------------

Item:

Genuine Modena 3pce Lightweight Jap Wheels

PCD: 5x114.3

F: 17x8.5 +45 with 225/45 (or +20 with the 25mm spacers)

R: 17x9.5 +38 with 245/40

Comments: These were brought in from Japan on a r34, they weigh less than my URAS NS-01's and are wider which suprised me a lot. I can throw in some 25mm hubcentric spacers for an extra $100

More Info:

http://www.nissansilvia.com/forums/index.p...=247279&hl=

Price: $600

Pics:

wheel2bc1.jpg

rims1tm9.jpg

dscn0029smalltp6.jpg

----------------------------------------------------------------------------------------------------------

Location:

SA, will post anywhere

Contact:

PM me

Link to comment
https://www.sau.com.au/forums/topic/211129-17-wheels-1-set-and-1-pair/
Share on other sites

shame your in SA..

Interested in the volks..

Any idea on shipping cost to Syd?

btw.. no rubber?

Interested if comes with rubber too..

Edited by GTS4WD

sydney freight is cheap, depends if u want all 3 and the 4th barrel or just the 2, sending just 2 ull obviously save u some $$

as i said i can throw in tyres, ive got a few 255/45's, a pair of 235/45's with bad camber wear but good tread over the rest of the tyre. or i can do them for $800 with pretty much brand new 235/45 pirelli dragons (top of the range performance tyre) as my mate has a pair for sale.

ill chuck u a PM and we can negotiate.

  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...