Jump to content
SAU Community

Recommended Posts

Item RB25/30

Age 2 years

Condition verygood

Price 10grand neg

To Fit any car

Kms around 25,000

location Tamworth

Comments

im selling my Rb25/30, 3540 turb, forged intenals, msd ignition, microtec comes with its own wiring harness, 48mm waste gate, hks lookalike blow off valve not fitted. Comes with 600x300mm cooler and stainless cooler piping to suit r32 if required for extra depends on how much the donk goes for. The motor is still in the car if u wanted to test. The whole car is for sale race car only roll cage alloy dash, rims let me no if ur interested. Only pm me or call me on 0414974099 Rob. Cheers guys.

R32 GTR box, 60 litre full cell in the boot all speed flow fittings external 040Bosch pump, sard presure reg, standed RB30 filter, fuel rail is custom made with RX7 injecters. Suspension is HSD with pillow ball tops on the front, hicas lock bar, ANDRA aproved 6 point roll cage, 17inch by 9.5inch koya drift teks, slotted front and rear RDA disc brakes near brand new did one powercruise with em with bendix pads, tacho,shift light, water temp, oil presure, boost gauge, all auto meter, brand new alloy radiator, battery relocated into the boot, wide mouth vertex front bar, brand new oil cooler oil filter relocater.

Thats all i can think of atm anythin els u wanna no just ask. Cheers

post-41069-1206504622_thumb.jpg

post-41069-1206504655_thumb.jpg

Edited by boostedlux
Link to comment
https://www.sau.com.au/forums/topic/212077-rb2530-3540-forged-internals-350bhp/
Share on other sites

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

so this will make a car that is not turbo, turbo? Because i have a RB25DE and it doesn't have the internals to put a turbo on it will this make my car turbo? thanks

so this will make a car that is not turbo, turbo? Because i have a RB25DE and it doesn't have the internals to put a turbo on it will this make my car turbo? thanks

U buy the motor put it in ur car and wulla u got urself a turbo car

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...