Jump to content
SAU Community

Recommended Posts

hehehe everytime i go past that place i see a line from these forums...

if its not whistlas its arsns (which looks like its coming along quite well) and then today i see preds :D Hopefully will have the bootlid holes welded up this weekend if this weather subsides a little for me tomorow and then MINE will join the masses down there :D

oh yeah, for those that have no idea what im talking about im talking about the panel beating joint in cheltenham :D

Link to comment
https://www.sau.com.au/forums/topic/21305-palm-the-new-skyline-hospital-d/
Share on other sites

hehe...yer, its a bit like that :D

Rang up yesterday. I was expecting a few weeks, but Con said mine should be ready sometime next week! woot! I was expecting 3 weeks or something, so pretty happy its a lot less than i expected. Hopefully its all sweet and as good as when i bought it (if not better)

They cut me a good deal on my grill and bumper, so that is all getting done too at the same time. Finally no more greyness !

  • 3 weeks later...
  • 3 weeks later...

need to go and visit and see how my babys going... need to see if they can get it done in the next couple of weeks... i need my car back the soarers driving me mental!! but at the sametime still fun to drive :)

Hey you're not driving a falcon that won't go above about 40km/hr up a hill, the head gasket is probably about to bust at any moment, and well I hate holding up traffic!! that is NOT fun anymore :)

My mate was in hysterics when he drove it the other day :)

Mine should be back in a few days I think.. go remind them to chase up that suspension place where it is atm!

its outside their shop without the front bar man i pass it every day :) i am going down tomorow to see when mines going to be ready.... i want it back :)

will ask con about ur one gords :)

Gordon - was just down at palm... my car should hopefully be ready in 2 weeks max :( ur car however is waiting on the front bar... suspensions been done its been sitting and waiting for a few days cause the front bar is ***t man.

there are cracks all thru it which will show up thru the entire paint job and con says he doesnt really want to paint it and have it leaving there looking like that. Honestly man id get a new front bar... maybe not something as low as that either... or just get a new 400r bar i spose... but the one thats their doesnt look crash hot.

hehe shes outside enjoying the sunshine :) very shiney i must say... dropped off the mesh and my car will be ready by next week... i cant go down until next friday anyways so thats whe i will be picking her up... give her the thrashing she so loves and then parking it for another 2 weeks until i pay my rego :D

hehe hey pred i seen ya car again today... looks pretty much the same :( theres a nice 350z down there now and im pretty sure i seen the rear end of my car.. which looked painted :D might pop down before work and take a look :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...