Jump to content
SAU Community

CRUISE TO RAISE MONEY FOR GREMLN (Jason) 17/AUG/2003 .... Please help


Recommended Posts

ok u give the $$$ 2 the guy wit the done up red wrx EVILRX, thats his plates aswell

ill put ur name on the list mate

ill also be in a black 200sx maybe if my mate goes

we have now got a proffessional photographer!~!!!!!!

this is the updated detials

http://forum.hot4s.com.au/messageview.cfm?...4&threadid=7305

is all that ok???

hey peepple heres the link 4 the after cruise thing

http://forum.hot4s.com.au/messageview.cfm?...4&threadid=7436

hey imflyn i saw ur car its sweet u spoke 2 1 of my mates an i was wit him

ill put pix up on that hot4s link latr i took 300 but its gonna take a while 2 load em all up so ill do it ASAP

Just checked out the pics, theres xome top shots there. Thanks to all the photo takers.

sw20gt, thanks for the compliment.

Wheels are coming soon, im just broke as at the moment.

Im still not finished with it yet. Theres still a long list in my garage of things to do.

Can you lend me $3500???? PLease. ha ha



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...