Jump to content
SAU Community

Recommended Posts

Hi all,

I need some questions answered.

My R33 series 1 has a wire come from the flooring and plugs into the bottom of my drivers and passenger side seats. Then another wire comes from there and hangs loosely with nothing connected. What is this for? Airbag? Should the wire just being sitting there loosely?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/21354-wiring-in-front-seats/
Share on other sites

Thanks,

But I found the problem is that when they removed the original seat belts, the wires were connected to where the belt connects. This would send a signal to the dash saying your seat belt is on or off. Just a safety feature.

So the new povo belts they put in would not have this feature and so the wires cannot be connected.

hey guys,

just a quick answer to shed some light on whether they can be used for anything else.... i wanted to hook some under seat neons up to them which would have been controlled by a switch on the dash, but before buying the neons i tested the currency of the plugs with a multimeter and found that there was less then 0.20volts going through, therefore there was not even 1volt going through, so i gave upon the idea of using them for neons..... i'm not saying i'm right, as it could just be my car, so can anyone else here test them as well to see whether u get the same results, as i really wanted to use them for some neons, perfect spot and all :P,

many thanks (interested to hear results now!!!!)

yeah, as stated above, I was told in my R32, that they are for the seat belt light. The chairs sense if someone is sitting in them ,and if the belt isnt on, the light on dash will flash.

For compliance the seatbelts are swapped as the jap ones dont have ADR approval. The seatbelt, and the seat belt thingy that it plugs into are swapped. Mybelts even have a different anchor bolt into the chassis near the door....

As this is only a small function, it wouldnt require much voltage.

Will

  • 5 weeks later...

Do all Skylines have air bags?

My series 1 GTST doesn't have an air bag at all (dash or wheel) and it has those wires under the seats!!! maybe rule thos options out!!

Has anyone looked at there new seat belts for front seats!! had my interior removed recentl;y and those seat belt moun ts done look very safe!!!

it's like a single bolt through thin body steel, going to a metal plate that the belt bolts onto!! any one else seen this!!!???

The wires are there in the R32's for the electric seat belt retainers - you may notice sometimes that the seat belt will not automatically retract or have any force on it wanting it to retract. As soon as you undo the belt from the buckle, it automatically retracts. This was as a comfort feature, I thought it was rather stupid personally and disconnected it, thus always having tension from the belt on my chest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...