Jump to content
SAU Community

Recommended Posts

Hi all,

I need some questions answered.

My R33 series 1 has a wire come from the flooring and plugs into the bottom of my drivers and passenger side seats. Then another wire comes from there and hangs loosely with nothing connected. What is this for? Airbag? Should the wire just being sitting there loosely?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/21354-wiring-in-front-seats/
Share on other sites

Thanks,

But I found the problem is that when they removed the original seat belts, the wires were connected to where the belt connects. This would send a signal to the dash saying your seat belt is on or off. Just a safety feature.

So the new povo belts they put in would not have this feature and so the wires cannot be connected.

hey guys,

just a quick answer to shed some light on whether they can be used for anything else.... i wanted to hook some under seat neons up to them which would have been controlled by a switch on the dash, but before buying the neons i tested the currency of the plugs with a multimeter and found that there was less then 0.20volts going through, therefore there was not even 1volt going through, so i gave upon the idea of using them for neons..... i'm not saying i'm right, as it could just be my car, so can anyone else here test them as well to see whether u get the same results, as i really wanted to use them for some neons, perfect spot and all :P,

many thanks (interested to hear results now!!!!)

yeah, as stated above, I was told in my R32, that they are for the seat belt light. The chairs sense if someone is sitting in them ,and if the belt isnt on, the light on dash will flash.

For compliance the seatbelts are swapped as the jap ones dont have ADR approval. The seatbelt, and the seat belt thingy that it plugs into are swapped. Mybelts even have a different anchor bolt into the chassis near the door....

As this is only a small function, it wouldnt require much voltage.

Will

  • 5 weeks later...

Do all Skylines have air bags?

My series 1 GTST doesn't have an air bag at all (dash or wheel) and it has those wires under the seats!!! maybe rule thos options out!!

Has anyone looked at there new seat belts for front seats!! had my interior removed recentl;y and those seat belt moun ts done look very safe!!!

it's like a single bolt through thin body steel, going to a metal plate that the belt bolts onto!! any one else seen this!!!???

The wires are there in the R32's for the electric seat belt retainers - you may notice sometimes that the seat belt will not automatically retract or have any force on it wanting it to retract. As soon as you undo the belt from the buckle, it automatically retracts. This was as a comfort feature, I thought it was rather stupid personally and disconnected it, thus always having tension from the belt on my chest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...