Jump to content
SAU Community

Where To Tune Wolf 3d V4

PWND

By PWND,
in Queensland

 Share

Recommended Posts

PWND Grand Master

PWND

Posted
Posted

As topic says,

just wondering if anybody knows any workshops that have had experience with the Wolf 3D?

Have found one at the right price, but before purchasing, as everybody always recommends find an ecu that your tuner prefers, figured i would see if there are any tuners locally, and roughly how much they would charge to install it for a rb25det.

Also, is the wolf even a good option or should I save a bit more extra cash and get the power fc? spent the last hour or so searching the web for reviews and tips, but am still none the wiser really.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/213739-where-to-tune-wolf-3d-v4/
Share on other sites
Revhead Grand Master

Revhead

Posted
Posted

Can't help with Wolf tuners, but I had exactly the same choice a few years back and ended up going with the PFC ($800 at the time lol)

I don't recall specifics but I remember thinking that the Wolf was a flat-out ECU, and didn't have some of the niceties that you'd want in a street car. I think it didn't have closed loop for starters, and the idle control wasn't great and didn't have aircon idle-up or something??? And I think the tuning is pretty coarse on it, 8 or so rpm/load points? As I said I haven't checked them in ages so I may be wrong or things may have improved with them since then, but it's worth looking into for yourself anyway.

PWND Grand Master

PWND

Posted
  • Author
Posted

been searching the forced induction section, and googling it, but so far not much. was doing it on dial up though, due to work only having dial up at my office, so was a slow process.

was hoping to find a tuner that has had experience with them, especially v4, so could talk to him myself, and see if the wolf and power fc were significantly different for my goals. attempting to build my r32 into a street registered circuit car. it's currently the daily, till my other car arrives in october/november.

at the moment the price difference between the two is around $300-400 for what I am able to find, in favour of the wolf. due to spending a bit on the car already, $300-400 at the moment is a significant difference, but just wondering whether it is significant enough, especially if the power fc is leagues ahead. i have seen cars with high numbers with wolf ecu's, but i still do want good idle, some fuel economy etc etc, and am wondering whether the wolf can deliver.

QWK32 Veteran

QWK32

Posted
Posted
Can't help with Wolf tuners, but I had exactly the same choice a few years back and ended up going with the PFC ($800 at the time lol)

I don't recall specifics but I remember thinking that the Wolf was a flat-out ECU, and didn't have some of the niceties that you'd want in a street car. I think it didn't have closed loop for starters, and the idle control wasn't great and didn't have aircon idle-up or something??? And I think the tuning is pretty coarse on it, 8 or so rpm/load points? As I said I haven't checked them in ages so I may be wrong or things may have improved with them since then, but it's worth looking into for yourself anyway.

jeeze, they have come a long way since then. the v4s and v4 plus do have closed loop, a/c idle correction and idle control. 16 load points at 125rpm increments up to 16000rpm. so they are a pritty good unit. i've just wired one into a mates car and am in the process of setting it up.

PWND, we have been given the number of a guy that will finish the tune if its running/idling and he is supposed to be good at wolfs. if you want a can dig that number up for you. but like i said, he will only touch it if it is already running. let me know.

PWND Grand Master

PWND

Posted
  • Author
Posted

mate, if you do find it, the number would be great.

it's a start, as at the moment I don't have any numbers for QLD.

Not very keen to just ring up shops and ask, as am a bit worried that they might say that they can install and tune it even though they have had no experience. That's why I was hoping to talk to somebody who has had experience with them

QWK32 Veteran

QWK32

Posted
Posted
mate, if you do find it, the number would be great.

it's a start, as at the moment I don't have any numbers for QLD.

Not very keen to just ring up shops and ask, as am a bit worried that they might say that they can install and tune it even though they have had no experience. That's why I was hoping to talk to somebody who has had experience with them

ok, i'll pm you later.

BelGarion Grand Master

BelGarion

Posted
Posted

lol

the wolf 3d v4 straight out destroyed the powerfc in my experience

spark cut rev limiter, map sensor, mine ran ls1 coilpacks.

powerfc is basicly a tunable stock ecu, theres a lot of things it cannot do that the wolf can. however unfortunatly finding someone who wants to tune it is a bit more difficult. that said there isnt anything wrong with their ability.

and as mentioned they will run your aircon ect fine.

bloodzkull Community Regular

bloodzkull

Posted
Posted
lol

the wolf 3d v4 straight out destroyed the powerfc in my experience

spark cut rev limiter, map sensor, mine ran ls1 coilpacks.

powerfc is basicly a tunable stock ecu, theres a lot of things it cannot do that the wolf can. however unfortunatly finding someone who wants to tune it is a bit more difficult. that said there isnt anything wrong with their ability.

and as mentioned they will run your aircon ect fine.

very true. did you know the power fc actually uses a factory nissan board in it.

give pete from rpm performance a call on 54993932. he shouldn't have a problem tuning the v4.

he tuned my v500 and did a great job. i actually upgraded from a PFC to the wolf and would never look back.

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Last person I spoke to was pi55ed that they were totally unhelpful with the cooling failures. He had to put a bag of ice on his to drive anywhere, and they sent a new one that was the same and couldn't be bothered after that. Never been a fan of Wolf products and I guess it shows. Get a PFC or get a Motec if you need to step up from that.

But if you want a reasonably priced tuner try Mick at Signature Performance in Ipswich. Has been looking after club members extremely well, and would turn his hand to any product with common sense and expertise without breaking your bank.

bloodzkull Community Regular

bloodzkull

Posted
Posted

^^hmmm very intresting. that was the v4 yeah? was it mounted in the kickpanel like stock? might be worth finding out if it is a common issue with the v4. i haven't had any problem the the v500 though.

strange that they didn't want to know about it. when i have dealt with wolf they have been more than helpfull. maybe just different person within the company or something

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a good German place in Brisbane if youre up for the drive 😛
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...