Jump to content
SAU Community

Tps Value Address

Vug5

By Vug5,
in General Maintenance

 Share

Recommended Posts

Vug5 Rookie

Vug5

Posted
Posted

Hi,

In attempting to track a trajectory on a map in Nissan datascan's "Map Trace" function, the TPS gets stuck on the minimum value. I recall that if U know the address of the TPS value, U can get this to work on any RB, SR, etc. My application is an RB20DET, stock CPU. Anyone know where the value is hiding? Also, any hints on how to extend the selection of available maps would be great.

Link to comment
https://www.sau.com.au/forums/topic/214246-tps-value-address/
Share on other sites
Vug5 Rookie

Vug5

Posted
  • Author
Posted

Thanks for rply,

Take a look at

inhibit_harvest_url_ttp://202.43.224.130/

with the "inhibit_harvest_url_" bit replaced by "h" of course.

point 10.

10. Map trace

  • A real time trace of a position on the map. This function is only available for z32 300zx cars at the moment. If the real time TP value address is known the function can be set up to work on any Consult I Nissan car.

The TP address is the spot in RAM in the ECU where the CPU stashes the TP (throttle pos). In datasacn, you can tell the map trace function this address. Then the map trace function can get its grubbies on the TP. Next U watch the track of the trottle/rpm curve pass over the timing and fuel map as you wind the car up. When you get ot a place you dont like the feel of, or it leans out or pings, you can tweak the map there :D That's assuming you know how to down & upload the maps. That leads to my second question. Does anone know how to give datascan more (read my custom) maps? That way, I could read my values off the display instead of having to look them up in a seperate app.

Vug5 Rookie

Vug5

Posted
  • Author
Posted

Further to that, it just occurred to me that the real time TP address might also be a memory mapped I/O register that the CPU reads to get the TP. Either way, it gives access to the TP for this particular datascan option.

NewKleer Mentor

NewKleer

Posted
Posted
TP memory addresses for VG30DETT, RB20DET and SR20DET identified by current NDS users are already pre-programmed.

get the latest version if you're using an old one - there is an option on dropdown for rb20det?

NewKleer Mentor

NewKleer

Posted
Posted

i think thats the point of it - they will read the maps from the rom and then display your position on it. because from memory once you choose your values it will then populate the table (fairly slowly, so presumably this point its reading from the map) before it starts showing you the trace

Vug5 Rookie

Vug5

Posted
  • Author
Posted

Yes, this is the way my old version works. I can't imagine that that would change, but U never know....

Shame we have to pay for the new one (hence all the questions), but it's not much.

Now, let's pop that rom out, solder in the piggyback, wire it up and were away....

No more soot on the boot...... :laugh:

Vug5 Rookie

Vug5

Posted
  • Author
Posted
Have you looked into nistune?

Intended to get something like a type 2 board, but no s/w.

Also will look into PC BIOS backup/switch boards & software. These ECU eprom sockets are obsolete,

and I expect there is junk out there for nothin'

Plenty of time.... It's a slug & I'm old, and patient.....

  • 1 month later...
YCOPY Enthusiast

YCOPY

Posted
Posted
Hi,

In attempting to track a trajectory on a map in Nissan datascan's "Map Trace" function, the TPS gets stuck on the minimum value. I recall that if U know the address of the TPS value, U can get this to work on any RB, SR, etc. My application is an RB20DET, stock CPU. Anyone know where the value is hiding? Also, any hints on how to extend the selection of available maps would be great.

So can this be done on and rb25det also?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I see what you mean on that last paragraph and makes sense. I am leaning towards because I made the repair/filler area large that I didn't use a long enough block. Will minimise the area and let you's know how I go. This is random but I noticed when I put epoxy primer it felt flat but that's just temporary.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Tried to repair with filler only. The block is a foam block but quite hard and I put a velcro on it for sandpaper, the hook and loop system. It's not one of those super soft ones that just follow the panel. Similar to a dura block.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      You need one of those automated sprays that puffs a nice small every 15 minutes in their room. Except swap the nice smell for chloroform...
    • MBS206
      Vag Coil Diy loom wire guage selection

      By MBS206 · Posted

      Don't step down power supply size, maintain it the whole way. It's how I'd do it. OR, Id have one feed, with one joint that splits out to six smaller gauge wires that go to each coil. I wouldn't add joins like stepping from 12 to 16, at the first two coils, as if you try to continue that fashion, each joint will introduce a voltage drop. In theory, earths should be the same size as power feeds, however in this case the main power needs to be bigger due to the average size current. So the next question is, how much current do these coils actually need?
    • MBS206
      Steps to DIY sanding car back ready for respray....

      By MBS206 · Posted

      I think Murray is onto it. It's sounding like either it's a soft block, not long enough block, OR if you're chasing waves, you're going in the direction of the waves, instead of across them. Rotate your sanding pattern by 45 degrees is something to try. You said you're going in an X, so now instead, from the same perspective, do a "t" instead.   If you're not able to have the block sit on top of two high points, and not touch the low point between them, you'll never get it flat.
×
×
  • Create New...