Jump to content
SAU Community

Recommended Posts

hey guys

a while ago if some of u remember i had a little issue as to boost spike.. look at dyno

EmreA-Dyno03-03-2007.jpg

was hitting 20psi then dropping to 16-17.

after the intake pipe poped off the turbo, i thought id pull it all out and clean my afm and tada!

the hose going to the bov (which is blocked off) had a massive tear around 15cm long!

i dont know why the workshop kept the hose there and blocked it off from around the bov location, anywho, blocked it off from the intake pipe itself..

now what id love to know is how can i lower my boost via the hks actuator? it was a little nut thingy on the end im 100% sure its adjustable just want to know how/which way! but now its running 20psi all day everyday :S

now thats all done, should i just leave the boost controlled by the actuator or should i set it to say 12psi and run a boost controller? or just run 15psi from actuator?

one problem is that the car will be on the track at winton (19th april), and i dont think i can get one of them turbotech boost controllers before then..

any ideas would be much appreciated!

thanks in advance

Edited by DjeMz

so you have a hks adjustable actuator and just want to know how to adjust it?

on my turbo you have to disconnect the arm from waste gate end then loosen the nut on the shaft, wind it out and tighten the nut again.

ye well its sorta gotta be done...

actually to think about it, its really not that hard.. shouldnt take more then 5 mins to do, then testing it (going for a drive) then setting it to the right amount of boost will take time (but fun =) )

The turbotech will work fine...adjusted right the hks actuator should see you running about 14-16psi without any spiking...then use the turbotech to raise boost to whatever level you want...remember that this is a mechanical system so a slight spike as it hits max boost is normal as it takes time for the system to stablelize...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...