Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

Stopped by Fibrevision today and spoke to Bruce.

We were waiting on an R34 coupe to come in but it's been over a month and it's a no show so far. We were going to see what EXACTLY needed to be done. But i've seen Bruce's work, 100% confident we can do it now.

But either way it will be done after I get back from Japan. Hoping January 2009. But I'm in no rush to be honest. :whistling:

Stopped by Fibrevision today and spoke to Bruce.

We were waiting on an R34 coupe to come in but it's been over a month and it's a no show so far. We were going to see what EXACTLY needed to be done. But i've seen Bruce's work, 100% confident we can do it now.

But either way it will be done after I get back from Japan. Hoping January 2009. But I'm in no rush to be honest. :laugh:

Good luck! hope to see a good result! i been looking into aswell.

  • 5 weeks later...

Well I COMPLETELY forgot (so did Bruce at FB) about the lower reverse lights on the R34 Coupe. As I saw my friend reverse his 2 door 34 onto my lawn I was like aww f**k!

I'm scrapping this idea, but I definitly encourage any high rollers with the coin to make it happen, I think it'd look mint.

Cost-wise you would need about $3,000 for the main brake lights area etc, and then I'd estimate a further 800-$1,000 for the lower reverse lights section.

In terms of what needs to be done, that Skylude post gives is a good example. http://www.cardomain.com/ride/553310

reshaping the bootlid to fit it in is the main thing that needs to be done. Decided not to go ahead as I'm aiming for a 34R late 2009, early '10. :)

Well I COMPLETELY forgot (so did Bruce at FB) about the lower reverse lights on the R34 Coupe. As I saw my friend reverse his 2 door 34 onto my lawn I was like aww f**k!

I'm scrapping this idea, but I definitely encourage any high rollers with the coin to make it happen, I think it'd look mint.

Cost-wise you would need about $3,000 for the main brake lights area etc, and then I'd estimate a further 800-$1,000 for the lower reverse lights section.

In terms of what needs to be done, that Skylude post gives is a good example. http://www.cardomain.com/ride/553310

reshaping the bootlid to fit it in is the main thing that needs to be done. Decided not to go ahead as I'm aiming for a 34R late 2009, early '10. :thumbsup:

looking at this: http://www.skylinesaustralia.com/forums/in...t&id=126480

and looking at the rear bar. would it be possible just to fit a coupe rear bar to your 4door for the lower reverse lights? they look very similar but theres probably slight differences that you cant tell from that pic

probably not as straightforward as that but still.

Edited by G0DZLR

Correct that would be the way to do it but a whole lot of modifying to fit and re-wiring, as the 2 door rear kit goes more around the sides then the sedan, and it's not a striaght swap. And of course the $$. So I'm bailing on the idea. Was good while it lasted. lol.

Edited by Magic

When I get the money I'll pick up the baton..

Good to know that fibrevision are up to the job though, I've sourced some GTR front fenders, some I'm doing my front end atm...

Will do the arse later down the track..

  • 8 years later...
  • 2 years later...
  • 2 years later...
  • 1 month later...
  • 1 year later...

I've been looking into the swap owning a sedan for a while and have managed to get a deal on a coupe  so I will do what I can and keep anyone who is still viewing this and wanting to see progression of it. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...