Jump to content
SAU Community

Recommended Posts

I want to do a compression test on my old crappy daily driver.. just to see how much life is left in it.

I've got a compression tester, but have no idea how to use it?? :D

Do i just stick in one of the cylinders (remove spark plug and stick in) and start the car up??

Or do i just stick it in and it will it give me a reading while the engine is not running?

Anybody who has slightly more of a clue than me (not much) of how to do it, please let me know :D

Link to comment
https://www.sau.com.au/forums/topic/21477-how-do-i-do-a-compression-test/
Share on other sites

Remove all spark plugs, I would also remove ignitor moduel plug to stop the sparks, hold throttle wide open, crank over 6 times, take reading, and do the same to all of them. pressure not that important as all gauges read different, most important is not having different pressures (eg, flatter battery lower pressure)

sherlock is right , i hope u have long stem on your compression gauge to rech the plug holes .

the engine should be hot and crank at 300 rpm .

u dont say what engine it is but here is a guide.

rb20e 1.23 mpa ( limit .93)rb25de 1.26 ( limit .96)rb25det1.2( limit .90)and rb 26dett 1.18 (limit .88) variance limit .10 mpa

crank the engine until the pressure does't go up anymore ( usualy a few seconds ) then record the reading it may be in psi on your gauge. 1 mpa =138 psi apr.

if u r pressure is down on 1 or more put some oil in the cil crank it a little then check pressure again if it goes up to normal it means u have worn piston rings , broken rings or chipped piston in that cil. if it doesn't make any diff then its leaking valve .

i hope that helps u in someway and as sherlock said dont wory if u r readings are low , maybe slow cranking speed or the gauge .

as long as they are all the same its good .

if they are all the same then put a little oil in the cil and try again if the reding is the same again its all good ( its unlikly that all valves are leaking the same amount .

Thanks for the very useful info.. this is actually for an old car (1987 XF Falcon..4.1L ), which has no such fancy thing as coil packs and things. The info provided will be useful for checking the compression though in that one. I have a factory workshop manual so I guess I can find the correct factory figures.

May also try on my RB25DET Skyline also.. i *think* the stalk is long enough but I know what you mean.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As Fred would tell us, it's all about interpreting the rules. It's not a water sprayer, it's a water mister... But everything else you've said, 100%! Even a raspberry Pi would be great, use HDMI out for a display, and add a raspberry Pi CANBus hat to read values out from the ECU.
    • Being a race car, and being in the era of the Arduino, one would think it would take little effort to build a controller to do the spraying based on a real physical measurment. Waaaaay back in the dim dark AS days, JE "designed" (as in, he had help) a microcontroller based intercooler spray system. It watched the difference between a temp sensor stuck on the core and one in the free air in front of the cooler, and if the temperature difference exceeded a (settable) threshold, it would activate the sprays. Thus, it only ran water when there was an actual need for water. If you stop to think about the actual physical things that are going on in that stack of coolers, there's probably at least a couple of triggering conditions one could come up with, and one could probably even run one pump with more than one solenoid valve, to allow water to be placed where it is needed, or at all points at once (if it is needed at all points). We're in the age of science baby. But.... I suspect that intercooler water sprays are on the forbidden list in most circuit classes, no? So only good for Targa type stuff?
    • I'll just leave this with, holy shit, those cars at work are awesome, and this will look wicked!
    • Could you modify this duct so instead it pushes the extra air through the radiator too and not down and out? For temps, I know it's not the greatest idea, but as a bit of a last resort, you could use a very intermittent misting spray onto the front of the coolers/rad. You don't want to be soaking them such that water is dripping off, but a small most on/off so that the water evaporates. That point of it constantly evaporating, rather than being soaked in water, will pull a LOT of heat out of the cooler. I'm literally thinking just the little mist sprayers for a garden from Bunnings. Being in a low humidity climate it will help even more! The other trick if you want to be ghetto is some shade cloth hung in the opening, and keep it wet. Pretty much now it's acting like an evap cooler on a house, but cooling the air you need to use to cool the radiator...   On a topic to think about too though, when air enters through the bumper, is it all nicely ducted from the edges of that opening back at a nice angle, or is it like most cars, and the edge of the opening just stops, and suddenly it's wayyy wider behind that? If it does the later, get it shrouded out at nice angles. When that opening changes too rapidly, it can actually cause a high pressure zone between the front bar and radiator, and limit air flow into that area, which means less air for cooling, as it effectively stalls the air, AND adds to drag...
    • Do you have any before and after photos? That's $200 just for the hydro blasting?
×
×
  • Create New...