Jump to content
SAU Community

Recommended Posts

hey guys

i just changed my indicators with my front bar, and the lamp is blinking really strange...

i think it has something to do with the resistance across the new circuit? anyone have any experience with this??

I need to increase the resistance across the wires or something to make them blink normally??

the lights are all working so its not a fused bulb..

any help appreciated! thanks.

Link to comment
https://www.sau.com.au/forums/topic/214793-aftermarket-turn-signal-indicators/
Share on other sites

hey guys

i just changed my indicators with my front bar, and the lamp is blinking really strange...

i think it has something to do with the resistance across the new circuit? anyone have any experience with this??

I need to increase the resistance across the wires or something to make them blink normally??

the lights are all working so its not a fused bulb..

any help appreciated! thanks.

LED lights will require a resister to increase the load on the circuit to normalise the blink rate

any shop that sells premade LED kits can get you a resister pack (or make your own)

i have the same problem, but not using any led lights.. how do i make a resistor pack?

you might need to play around with the resistances required - go to a jaycar and have a chat to them about it, you can buy smaller resisters that wire inline with the power, should fix it up.

i have the same problem, but not using any led lights.. how do i make a resistor pack?

Unless you've managed to change wattages on your globes (unlikely) you'll probably find one of your indicator lights aren't working.

Most indicator flasher units are load based, which means if you run LED, or drop a light it will flash quicker (reverse is also true).

Resistor packs create a false load to maker every thing work correctly.

it is true that if one indicator blows then they blink fast but all 6 of mine are working 100%

they blink at the normal rate with the hazard lights on but fast when its indicating

the indicators i put on the front were a bit smaller than the other ones so im thinking less resistance?

ill go into jaycar and look for some inline resistors

cheers

hey guys

i just dropped by jaycar today and picked up a 10W 1ohm ceramic resistor for $1.50.

placed it in PARALLEL across the circuit, now the thing blinks fine! maybe even a bit too slow! haha. but that can probably be changed by swapping the resistor for a 2 or 3 ohm one..

mine DIDN'T WORK when in series, still got me a little puzzled.. but that may be a wiring issue.. the resistor heats up a fair bit when in use, but we'll see how that goes in the long run.

hey guys

i just dropped by jaycar today and picked up a 10W 1ohm ceramic resistor for $1.50.

placed it in PARALLEL across the circuit, now the thing blinks fine! maybe even a bit too slow! haha. but that can probably be changed by swapping the resistor for a 2 or 3 ohm one..

mine DIDN'T WORK when in series, still got me a little puzzled.. but that may be a wiring issue.. the resistor heats up a fair bit when in use, but we'll see how that goes in the long run.

well good to see it works now without driving you insane lol

yeah last resister i used i had in series for LED's, but sounds correct in parrallel as it simulates a higher drain accross the circuit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...